• <delect id="tgu09"></delect>
    <nobr id="tgu09"><output id="tgu09"></output></nobr>
    <em id="tgu09"><label id="tgu09"><wbr id="tgu09"></wbr></label></em>
    參數資料
    型號: HR10A-10R-12SB(71)
    元件分類: 圓形連接器
    英文描述: 12 CONTACT(S), ZINC ALLOY AND BRASS, FEMALE, CIRCULAR CONNECTOR, SOLDER, RECEPTACLE
    文件頁數: 3/20頁
    文件大?。?/td> 2215K
    代理商: HR10A-10R-12SB(71)
    189
    HR10 SeriesPush-Pull Connectors
    Cable connecting methods
    HR10B-2.5CP
    HR10B-2.5CJ
    1.Cable end treatment
    Fig.1
    1.Dimensions for cable end treatment are shown in
    Fig 1.
    2.Termination is described below.
    (1).Strip cable outer jacket as indicated.
    (2).Slit outer jacket on both sides per Fig.1.
    (3).Fold back outer cover.
    (4).Remove insulator from cable.
    2.Soldering male pin to cable center
    conductor.
    Fig.2
    1.Solder male pin to cable center conductor as
    indicated in Fig.2.
    (1).Pre-solder the solder pot of pin with 0.5mm
    string solder.
    (2).Male pin should fit flush against the cable
    insulator as shown.
    (3).Remove any excess solder from the pin with a
    knife.This surface must be smooth.
    (4).A properly soldered terminal will yield 500gf
    when stretched.
    3.Crimping cable outer conductor
    Fig.3
    1.Insert cable prepared per PROCESS 2 into the
    connector.The cable should be inserted until it
    comes to a full stop.This may be verified by
    checking the dimension from the side of the
    connector to the top of the contact(as indicated in
    Fig 3). This dimension should be A.
    2.Crimp this installed metal clamp with tool HR10-
    TC-01 per Fig.3 and remove excess insulation with
    a knife.
    It is possible to pull back the contact.
    Hold cable when crimping metal clamp and keep
    the dimension to show in Fig 3. after crimping metal
    clamp.
    11±0.5
    1.4±0.2
    3.7±0.2
    (2.5)
    Slit cable outer jaket
    2 pieces (180° reverse side)
    Malu pin or Female pin
    Soldering
    Should fix flush
    Contact fixing jig
    such as vise
    Clamp metal
    (HR10B-2.5CP)
    A
    Connector
    Remove excess insulator
    material (remaining after
    clamping is complated)
    with a knife or aimilarobject.
    Table 1 dimenshion A
    2.5CP
    2.5CJ
    1.5±0.2mm
    0
    mm
    +0.3
    0
    相關PDF資料
    PDF描述
    HR10A-10R-12SC(71) 12 CONTACT(S), ZINC ALLOY AND BRASS, FEMALE, CIRCULAR CONNECTOR, CRIMP, RECEPTACLE
    HR10A-10R-20PC(73) 20 CONTACT(S), ZINC ALLOY AND BRASS, MALE, CIRCULAR CONNECTOR, CRIMP, RECEPTACLE
    HR10A-10P-10SC(73) 10 CONTACT(S), ZINC ALLOY AND BRASS, FEMALE, CIRCULAR CONNECTOR, CRIMP, PLUG
    HR10-10J-12P(73) 12 CONTACT(S), ZINC ALLOY AND BRASS, MALE, CIRCULAR CONNECTOR, JACK
    HR10-10J-12S(73) 12 CONTACT(S), ZINC ALLOY AND BRASS, FEMALE, CIRCULAR CONNECTOR, JACK
    相關代理商/技術參數
    參數描述
    HR10A-10R-12SB-MOD 制造商:Hirose 功能描述:MODIFIED LEAD 0.065 INCH
    HR10A-10R-12SC 功能描述:CONN HR10A RECEPT 12POS FEMALE RoHS:否 類別:連接器,互連式 >> 圓形 - 外殼 系列:HR10A 標準包裝:1 系列:軍用, MIL-DTL-38999 系列 III, ACT 連接器類型:母觸點插座 位置數:5 外殼尺寸 - 插件:15-5 外殼尺寸,MIL:D 觸點類型::壓接 觸點尺寸:16 安裝類型:面板安裝,隔墻式(前端螺母) 緊固型:有螺紋 方向:N(正常型) 外殼材料,表面處理:合成物,草綠色鎘鍍層 防護等級:抗環境影響 特點:屏蔽 包裝:散裝 請注意:不提供觸點 其它名稱:DD38999/24JD5BN
    HR10A-10R-12SC(71) 功能描述:環形推拉式連接器 12P RECP SHELL SZ 10 FEMALE CRIMP RoHS:否 制造商:Hirose Connector 產品類型:Connectors 系列:HR10 觸點類型:Socket (Female) 外殼類型:Receptacle 觸點數量:4 外殼大小:7 安裝風格:Panel 端接類型:Solder 電流額定值:2 A
    HR10A-10R-12SD(01) 制造商:Hirose 功能描述:CONN RECEPT 12POS FMALE DIP GOLD
    HR10A-10R-12SD(72) 功能描述:環形推拉式連接器 REC 12P FEM DIP GOLD RoHS:否 制造商:Hirose Connector 產品類型:Connectors 系列:HR10 觸點類型:Socket (Female) 外殼類型:Receptacle 觸點數量:4 外殼大小:7 安裝風格:Panel 端接類型:Solder 電流額定值:2 A