- 您現在的位置：買賣IC網 > PDF目錄370688 > HSDL-3201 Low Power Compliant 115.2 kb/s Infrared Transceiver(115.2 kb/s紅外順應收發器) PDF資料下載
參數資料
| 型號： | HSDL-3201 |
| 英文描述： | Low Power Compliant 115.2 kb/s Infrared Transceiver(115.2 kb/s紅外順應收發器) |
| 中文描述： | 低功耗符合115.2 kb / s的紅外收發器（115.2 kb / s的紅外順應收發器） |
| 文件頁數： | 12/16頁 |
| 文件大小： | 237K |
| 代理商： | HSDL-3201 |
12
Recommended Solder
Paste/Cream Volume for
Castellation Joints
Based on calculation and experi-
ment, the printed solder paste
volume required per castellation
pad is
0.22 cubic mm
(based on
either no-clean or aqueous solder
cream types with typically 60% to
65% solid content by volume).
Using the recommended stencil
results in this volume of solder
paste.
Pick and Place
Misalignment Tolerance
and Self-Alignment after
Solder Reflow
If the printed solder paste volume
is adequate, the HSDL-3201
will
self align after solder reflow.
Units should be properly reflowed
in IR/Hot Air convection oven
using the recommended reflow
profile. The direction of board
travel does not matter.
Direction Definition
Tolerance for X- axis
Alignment of Castellation
Misalignment of castellation to
the land pad should not exceed
0.2 mm or about one half the
width of the castellation during
placement of the unit. The
castellations will self-align to the
pads during solder reflow.
Tolerance for Rotational
(
θ
) Misalignment
Mounted units should not be
rotated more than
±
3 degrees
with reference to center X-Y as
shown in the direction definition.
Units that are rotated more than
±
3 degrees will not self align
after solder reflow. Units with
less than a
±
3 degree misalign-
ment will self-align after solder
reflow.
Allowable Misalignment
Direction
X
Y
θ
Tolerance
≤
0.2 mm
See text
≤
±
3 degrees
Y- axis Misalignment of
Castellation
In the Y direction, the HSDL-3201
does not self align after solder
reflow. Agilent recommends that
the part be placed in line with the
fiducial mark (mid-length of land
pad.) This will enable sufficient
land length (minimum of one half
of the land pad) to form a good
joint. See the drawing below.
Y
θ
X
MINIMUM 1/2 THE LENGTH
OF THE LAND PAD
EDGE
FIDUCIAL
相關PDF資料 |
PDF描述 |
|---|---|
| HSDL-4230 | High-Performance T-1 3 /4 (5 mm) TS AlGaAs Infrared (875 nm) Lamp(高性能T-1 3 /4 (5 mm)透明物質鋁砷化鎵紅外線(875 nm)照明燈) |
| HSDL-4400 | High-Performance IR Emitter Photodiode in Subminiature SMT Package(高性能 IR發射器光二極管（微型SMT封裝）) |
| HSDL-5400 | High-Performance IR PIN Photodiode in Subminiature SMT Package(高性能 IR發射器光二極管（微型SMT封裝）) |
| HSDL-4420 | High-Performance IR Emitter Photodiode in Subminiature SMT Package(高性能 IR發射器光二極管（微型SMT封裝）) |
| HSDL-5420 | High-Performance IR PIN Photodiode in Subminiature SMT Package(高性能 IR PIN 光二極管（微型SMT封裝）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HSDL-3201#001 | 功能描述:紅外收發器 IR Transceiver 115.2Kb/s RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| HSDL-3201#008 | 功能描述:紅外收發器 IR Transceiver 115.2Kb/s RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| HSDL-3201#011 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HSDL-3201#018 | 制造商:LITEON 功能描述:IrDA Data 1.4 Compliant 4 Mb/s 3V Infrared Transceiver |
| HSDL-3201#021 | 功能描述:紅外收發器 IR Transceiver 115.2Kb/s RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。