- 您現在的位置：買賣IC網 > PDF目錄9613 > ICL3221ECV-T (Intersil)IC TXRX SGL RS232 3-5.5V 16TSSOP PDF資料下載
參數資料
| 型號： | ICL3221ECV-T |
| 廠商： | Intersil |
| 文件頁數： | 10/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX SGL RS232 3-5.5V 16TSSOP |
| 標準包裝： | 2,500 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS232 |
| 電源電壓： | 3 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
18
FN4910.21
February 22, 2010
Devices with the automatic power-down feature include
an INVALID output signal, which switches low to indicate
that invalid levels have persisted on all of the receiver
inputs for more than 30s (see Figure 7). INVALID
switches high 1s after detecting a valid RS-232 level on
a receiver input. INVALID operates in all modes (forced
or automatic power-down, or forced on), so it is also
useful for systems employing manual power-down
circuitry. When automatic power-down is utilized,
INVALID = 0 indicates that the ICL32xxE is in
power-down mode.
The time to recover from automatic power-down mode is
typically 100s.
Receiver ENABLE Control
(ICL3221E, ICL3222E, ICL3223E, ICL3241E
Only)
Several devices also feature an EN input to control the
receiver outputs. Driving EN high disables all the
inverting (standard) receiver outputs placing them in a
high impedance state. This is useful to eliminate supply
current, due to a receiver output forward biasing the
protection diode, when driving the input of a powered
input has no effect on transmitter nor monitor (ROUTB)
outputs.
Capacitor Selection
The charge pumps require 0.1F capacitors for 3.3V
operation. For other supply voltages refer to Table 3 for
capacitor values. Do not use values smaller than those
listed in Table 3. Increasing the capacitor values (by a
factor of 2) reduces ripple on the transmitter outputs and
slightly reduces power consumption. C2, C3, and C4 can
be increased without increasing C1’s value, however, do
not increase C1 without also increasing C2, C3, and C4 to
maintain the proper ratios (C1 to the other capacitors).
When using minimum required capacitor values, make
sure that capacitor values do not degrade excessively
with temperature. If in doubt, use capacitors with a
larger nominal value. The capacitor’s equivalent series
resistance (ESR) usually rises at low temperatures and it
influences the amount of ripple on V+ and V-.
Power Supply Decoupling
In most circumstances a 0.1F bypass capacitor is
adequate. In applications that are particularly sensitive
to power supply noise, decouple VCC to ground with a
capacitor of the same value as the charge-pump
capacitor C1. Connect the bypass capacitor as close as
possible to the IC.
Operation Down to 2.7V
ICL32xxE transmitter outputs meet RS-562 levels
(±3.7V), at full data rate, with VCC as low as 2.7V.
RS-562 levels typically ensure interoperability with
RS-232 devices.
Transmitter Outputs when
Exiting Power-Down
Figure 8 shows the response of two transmitter outputs
when exiting power-down mode. As they activate, the
two transmitter outputs properly go to opposite RS-232
levels, with no glitching, ringing, nor undesirable
transients. Each transmitter is loaded with 3kΩ in parallel
with 2500pF. Note that the transmitters enable only
when the magnitude of the supplies exceed
approximately 3V..
Mouse Driveability
The ICL3241E and ICL3243E have been specifically
designed to power a serial mouse while operating from
low voltage supplies. Figure 9 shows the transmitter
RECEIVER
INPUTS
TRANSMITTER
OUTPUTS
INVALID
OUTPUT
V+
VCC
0
V-
VCC
0
tINVL
tINVH
INVALID
REGION
}
FIGURE 7. AUTOMATIC POWER-DOWN AND
INVALID TIMING DIAGRAMS
AUTOPWDN
PWR UP
TABLE 3. REQUIRED CAPACITOR VALUES
VCC
(V)
C1
(F)
C2, C3, C4
(F)
3.0 to 3.6
0.1
4.5 to 5.5
0.047
0.33
3.0 to 5.5
0.1
0.47
TIME (20s/DIV)
T1
T2
2V/DIV
5V/DIV
VCC = +3.3V
FORCEOFF
FIGURE 8. TRANSMITTER OUTPUTS WHEN EXITING
POWER-DOWN
C1 - C4 = 0.1F
ICL3221E, ICL3222E, ICL3223E, ICL3232E, ICL3241E, ICL3243E
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J4D-MW-B1 | CONVERTER MOD DC/DC 85V 100W |
| ICL3221ECV | IC TXRX SGL RS232 3-5.5V 16TSSOP |
| VI-J21-MX-F1 | CONVERTER MOD DC/DC 12V 75W |
| VI-J4B-MW-B1 | CONVERTER MOD DC/DC 95V 100W |
| ICL3221ECAZA-T | IC TXRX SGL RS232 3-5.5V 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL3221ECVZ | 功能描述:RS-232接口集成電路 RS232 3V 1D/1R 15KV AUTODWN COM RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ICL3221ECVZ | 制造商:Intersil Corporation 功能描述:Transceiver IC |
| ICL3221ECVZ-T | 功能描述:RS-232接口集成電路 RS232 3V 1D/1R 15KV AUTODWN COM RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ICL3221EIA | 功能描述:IC TXRX SGL RS232 3-5.5V 16SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ICL3221EIA-T | 功能描述:IC TXRX SGL RS232 3-5.5V 16SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。