FN4910.21 February 22, 2010 ICL3241E and ICL3243E monitor receivers remain active even during manual power-down and forced receiver disable, ma" />
參數資料
型號: ICL3223EIV
廠商: Intersil
文件頁數: 7/33頁
文件大?。?/td> 0K
描述: IC 2DRVR/2RCVR RS232 3V 20-TSSOP
標準包裝: 74
類型: 收發器
驅動器/接收器數: 2/2
規程: RS232
電源電壓: 3 V ~ 5.5 V
安裝類型: 表面貼裝
封裝/外殼: 20-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 20-TSSOP
包裝: 管件
15
FN4910.21
February 22, 2010
ICL3241E and ICL3243E monitor receivers remain
active even during manual power-down and forced
receiver disable, making them extremely useful for
Ring Indicator monitoring. Standard receivers driving
powered down peripherals must be disabled to
prevent current flow through the peripheral’s
protection diodes (see Figures 2 and 3). This renders
them useless for wake up functions, but the
corresponding monitor receiver can be dedicated to
this task as shown in Figure 3.
Low Power Operation
These 3V devices require a nominal supply current of
0.3mA, even at VCC = 5.5V, during normal operation
(not in power-down mode). This is considerably less
than the 5mA to 11mA current required by comparable
5V RS-232 devices, allowing users to reduce system
power simply by switching to this new family.
Pin Compatible Replacements for 5V
Devices
The ICL3221E, ICL3222E, ICL3232E are pin compatible
with existing 5V RS-232 transceivers - See the
“Features” section on page 1 for details.
This pin compatibility coupled with the low ICC and
wide operating supply range, make the ICL32xxE
potential lower power, higher performance drop-in
replacements for existing 5V applications. As long as
the ±5V RS-232 output swings are acceptable, and
transmitter input pull-up resistors aren’t required, the
IICL32xxE should work in most 5V applications.
When replacing a device in an existing 5V application,
it is acceptable to terminate C3 to VCC as shown on
Nevertheless, terminate C3 to GND if possible, as
slightly better performance results from this
configuration.
Power-Down Functionality
(Except ICL3232E)
The already low current requirement drops
significantly when the device enters power-down
mode. In power-down, supply current drops to 1A,
because the on-chip charge pump turns off (V+
collapses to VCC, V- collapses to GND), and the
transmitter outputs three-state. Inverting receiver
outputs may or may not disable in power-down; refer
to Table 2 for details. This micro-power mode makes
these devices ideal for battery powered and portable
applications.
Software Controlled (Manual) Power-Down
Most devices in the ICL32xxE family provide pins that
allow the user to force the IC into the low power,
standby state.
On the ICL3222E and ICL3241E, the power-down
control is via a simple shutdown (SHDN) pin. Driving
this pin high enables normal operation, while driving it
low forces the IC into its power-down state. Connect
SHDN to VCC if the power-down function isn’t needed.
Note that all the receiver outputs remain enabled
during shutdown (see Table 2). For the lowest power
consumption during power-down, the receivers should
also be disabled by driving the EN input high (see next
section, and Figures 2 and 3).
The ICL3221E, ICL3223E, and ICL3243E utilize a two
pin approach where the FORCEON and FORCEOFF
inputs determine the IC’s mode. For always enabled
operation, FORCEON and FORCEOFF are both strapped
high. To switch between active and power-down
modes, under logic or software control, only the
FORCEOFF input need be driven. The FORCEON state
isn’t critical, as FORCEOFF dominates over FORCEON.
Nevertheless, if strictly manual control over power-
down is desired, the user must strap FORCEON high to
disable the automatic power-down circuitry. ICL3243E
inverting (standard) receiver outputs also disable when
the device is in manual power-down, thereby
eliminating the possible current path through a
shutdown peripheral’s input protection diode (see
Figures 2 and 3).
RXOUT
GND ≤ VROUT ≤ VCC
5kΩ
RXIN
-25V ≤ VRIN ≤ +25V
GND
VCC
FIGURE 1. INVERTING RECEIVER CONNECTIONS
TABLE 2. POWER-DOWN AND ENABLE LOGIC TRUTH TABLE
RS-232
SIGNAL
PRESENT
AT
RECEIVER
INPUT?
FORCEOFF
OR SHDN
INPUT
FORCEON
INPUT
EN
INPUT
TRANSMITTER
OUTPUTS
RECEIVER
OUTPUTS
ROUTB
OUTPUTS
(NOTE 7)
INVALID
OUTPUT
MODE OF
OPERATION
ICL3222E, ICL3241E
N/A
L
N/A
L
High-Z
Active
N/A
Manual Power-Down
N/A
L
N/A
H
High-Z
Active
N/A
Manual Power-Down with
Receiver Disabled
N/A
H
N/A
L
Active
N/A
Normal Operation
N/A
H
N/A
H
Active
High-Z
Active
N/A
Normal Operation with
Receiver Disabled
ICL3221E, ICL3222E, ICL3223E, ICL3232E, ICL3241E, ICL3243E
相關PDF資料
PDF描述
ICL3223CP IC 2DRVR/2RCVR RS232 3V 20-DIP
MS3122E24-61S CONN RCPT 61POS BOX MNT W/SCKT
M83723/71W1002Y CONN RCPT 2POS WALL MT W/SCKT
VE-21H-MX-F1 CONVERTER MOD DC/DC 52V 75W
MS27468T25B46PB CONN RCPT 46POS JAM NUT W/PINS
相關代理商/技術參數
參數描述
ICL3223EIV-T 功能描述:IC 2DRVR/2RCVR RS232 3V 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
ICL3223EIVZ 功能描述:RS-232接口集成電路 RS232 3V 2D/2R 15KV AUTODWN IND RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
ICL3223EIVZ-T 功能描述:RS-232接口集成電路 RS232 3V 2D/2R 15KV AUTODWN INDEL RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
ICL3223EIVZ-T7A 功能描述:RS-232接口集成電路 RS232 3V 2D/2R 15KV AUTODWN IND RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
ICL3223IA 功能描述:IC 2DRVR/2RCVR RS232 3V 20-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器,接收器,收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC(0.295",7.50mm 寬) 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)