FN4910.21 February 22, 2010 ICL3241E and ICL3243E monitor receivers remain active even during manual power-down and forced receiver disable, ma" />
參數資料
型號： ICL3243ECB-T
廠商： Intersil
文件頁數： 7/33頁
文件大小： 0K
描述： IC 3DRVR/5RCVR RS232 3V 28-SOIC
標準包裝： 1,000
類型： 收發器
驅動器/接收器數： 3/5
規程： RS232
電源電壓： 3 V ~ 5.5 V
安裝類型： 表面貼裝
封裝/外殼： 28-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 28-SOIC W
包裝： 帶卷 (TR)
15
FN4910.21
February 22, 2010
ICL3241E and ICL3243E monitor receivers remain
active even during manual power-down and forced
receiver disable, making them extremely useful for
Ring Indicator monitoring. Standard receivers driving
powered down peripherals must be disabled to
prevent current flow through the peripheral’s
protection diodes (see Figures 2 and 3). This renders
them useless for wake up functions, but the
corresponding monitor receiver can be dedicated to
this task as shown in Figure 3.
Low Power Operation
These 3V devices require a nominal supply current of
0.3mA, even at VCC = 5.5V, during normal operation
(not in power-down mode). This is considerably less
than the 5mA to 11mA current required by comparable
5V RS-232 devices, allowing users to reduce system
power simply by switching to this new family.
Pin Compatible Replacements for 5V
Devices
The ICL3221E, ICL3222E, ICL3232E are pin compatible
with existing 5V RS-232 transceivers - See the
“Features” section on page 1 for details.
This pin compatibility coupled with the low ICC and
wide operating supply range, make the ICL32xxE
potential lower power, higher performance drop-in
replacements for existing 5V applications. As long as
the ±5V RS-232 output swings are acceptable, and
transmitter input pull-up resistors aren’t required, the
IICL32xxE should work in most 5V applications.
When replacing a device in an existing 5V application,
it is acceptable to terminate C3 to VCC as shown on
Nevertheless, terminate C3 to GND if possible, as
slightly better performance results from this
configuration.
Power-Down Functionality
(Except ICL3232E)
The already low current requirement drops
significantly when the device enters power-down
mode. In power-down, supply current drops to 1A,
because the on-chip charge pump turns off (V+
collapses to VCC, V- collapses to GND), and the
transmitter outputs three-state. Inverting receiver
outputs may or may not disable in power-down; refer
to Table 2 for details. This micro-power mode makes
these devices ideal for battery powered and portable
applications.
Software Controlled (Manual) Power-Down
Most devices in the ICL32xxE family provide pins that
allow the user to force the IC into the low power,
standby state.
On the ICL3222E and ICL3241E, the power-down
control is via a simple shutdown (SHDN) pin. Driving
this pin high enables normal operation, while driving it
low forces the IC into its power-down state. Connect
SHDN to VCC if the power-down function isn’t needed.
Note that all the receiver outputs remain enabled
during shutdown (see Table 2). For the lowest power
consumption during power-down, the receivers should
also be disabled by driving the EN input high (see next
section, and Figures 2 and 3).
The ICL3221E, ICL3223E, and ICL3243E utilize a two
pin approach where the FORCEON and FORCEOFF
inputs determine the IC’s mode. For always enabled
operation, FORCEON and FORCEOFF are both strapped
high. To switch between active and power-down
modes, under logic or software control, only the
FORCEOFF input need be driven. The FORCEON state
isn’t critical, as FORCEOFF dominates over FORCEON.
Nevertheless, if strictly manual control over power-
down is desired, the user must strap FORCEON high to
disable the automatic power-down circuitry. ICL3243E
inverting (standard) receiver outputs also disable when
the device is in manual power-down, thereby
eliminating the possible current path through a
shutdown peripheral’s input protection diode (see
Figures 2 and 3).
RXOUT
GND ≤ VROUT ≤ VCC
5kΩ
RXIN
-25V ≤ VRIN ≤ +25V
GND
VCC
FIGURE 1. INVERTING RECEIVER CONNECTIONS
TABLE 2. POWER-DOWN AND ENABLE LOGIC TRUTH TABLE
RS-232
SIGNAL
PRESENT
AT
RECEIVER
INPUT?
FORCEOFF
OR SHDN
INPUT
FORCEON
INPUT
EN
INPUT
TRANSMITTER
OUTPUTS
RECEIVER
OUTPUTS
ROUTB
OUTPUTS
(NOTE 7)
INVALID
OUTPUT
MODE OF
OPERATION
ICL3222E, ICL3241E
N/A
L
N/A
L
High-Z
Active
N/A
Manual Power-Down
N/A
L
N/A
H
High-Z
Active
N/A
Manual Power-Down with
Receiver Disabled
N/A
H
N/A
L
Active
N/A
Normal Operation
N/A
H
N/A
H
Active
High-Z
Active
N/A
Normal Operation with
Receiver Disabled
ICL3221E, ICL3222E, ICL3223E, ICL3232E, ICL3241E, ICL3243E
相關PDF資料
PDF描述
ICL3243ECB IC 3DRVR/5RCVR RS232 3V 28-SOIC
ICL3243ECA-T IC 3DRVR/5RCVR RS232 3V 28-SSOP
ICL3243CV-T IC 3DRVR/5RCVR RS232 3V 28-TSSO+
ICL3241IA-T IC 3DRVR/5RCVR RS232 3V 28-SSOP
ICL3243CV IC 3DRVR/5RCVR RS232 3V 28-TSSOP
相關代理商/技術參數
參數描述
ICL3243ECBZ 功能描述:RS-232接口集成電路 RS232 3V 3D/5R 15KV AUTODWN 28 COM RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
ICL3243ECBZ-T 功能描述:RS-232接口集成電路 RS232 3V 3D/5R 15KV AUTODWN 28 COMEL RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝:
ICL3243ECR 制造商:Intersil Corporation 功能描述:
ICL3243ECV 功能描述:IC 3DRVR/5RCVR RS232 3V 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件
ICL3243ECV-T 功能描述:IC 3DRVR/5RCVR RS232 3V 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*