- 您現在的位置：買賣IC網 > PDF目錄383092 > ICM7226 (Intersil Corporation) 8-Digit, Multi-Function, Frequency Counter/Timer PDF資料下載
參數資料
| 型號： | ICM7226 |
| 廠商： | Intersil Corporation |
| 元件分類： | 通用總線功能 |
| 英文描述： | 8-Digit, Multi-Function, Frequency Counter/Timer |
| 中文描述： | 8位數字，多功能，頻率計數器/計時器 |
| 文件頁數： | 10/19頁 |
| 文件大?。?/td> | 173K |
| 代理商： | ICM7226 |
9-24
RST IN Input
The RST IN is provided to reset the Main Counter, stop any
measurement in progress, and enable the display latches,
resulting in the all zero display. It is suggested to have a
capacitor at this input to V
SS
to prevent any hangup problem
on power up. See application circuits.
EXT RANGE Input
This input is provided to select ranges other than those
provided in the chip. In any mode of measurement the duration
of measurement is determined by the EXT RANGE if this input
is enabled. This input is sampled at 10ms intervals by the
100Hz reference derived from the timebase. Figure 12 shows
the relationship between this input, 100Hz reference signal and
MEAS IN PROGRESS. EXT RANGE can change state
anywhere during the period of 100Hz reference by will be
sampled at the trailing edge of the period to start or stop
measurement.
This input should not be used for short arbitrary ranges
(because of its sampling period), it is provided for very long
gating purposes. A way of using the ICM7226 for a short
arbitrary range is to feed the gating signal into the INPUT B
and run the device in the Frequency Ratio mode. Note that
the gating period will be from one positive edge until the next
positive edge of INPUT B (0.01s/1 cycle range).
MEAS IN PROGRESS, STORE, RST OUT Outputs
These outputs are provided for external system interfacing.
MEAS IN PROGRESS stays low during measurements and
goes high for intervals between measurements. Figure 13
shows the relationship between these outputs for intervals
between measurements. All these outputs can drive a low
power Schottky TTL. The MEAS IN PROGRESS can drive
one ECL load if the ECL device is powered from the same
power supply as the ICM7226.
BCD Outputs
The BCD representation of each display digit is available at
the BCD outputs in a multiplexed fashion. See Table 3 for dig-
its truth table. The BCD output of each digit is available when
its corresponding digit output is activated. Note that the digit
outputs are multiplexed from D8 (MSD) to D1 (LSD). The pos-
itive going (ICM7226A, common anode) or the negative going
(ICM7226B, common cathode) digit drive signals lag the BCD
data by 2
μ
s to 6
μ
s. This starting edge of each digit drive sig-
nal should be used to externally latch the BCD data. Each
BCD output drives one low power Schottky TTL load. Leading
zero blanking has no effect on the BCD outputs.
BUF OSC OUT Output
The BUFFered OSCillator OUTput is provided for use of the
on-board oscillator signal, without loading the oscillator itself.
This output can drive one low power Schottky TTL load. Care
should be taken to minimize capacitive loading on this pin.
Decimal Point Position
Table 4 shows the decimal point position for different modes
of lCM7226 operation. Note that the digit 1 is the least signif-
icant digit. Table is given for 10MHz timebase frequency.
REFERENCE
COUNTER
CLOCK
MEAS
IN PROGRESS
EXT RANGE
INPUT
t
r
FIGURE 12. EXTERNAL RANGE INPUT TO END OF
MEASUREMENT IN PROGRESS
TABLE 3. TRUTH TABLE BCD OUTPUTS
NUMBER
0
1
2
3
4
5
6
7
8
9
BCD 8
PIN 7
0
0
0
0
0
0
0
0
1
1
BCD 4
PIN 6
0
0
0
0
1
1
1
1
0
0
BCD 2
PIN 17
0
0
1
1
0
0
1
1
0
0
BCD 1
PIN 18
0
1
0
1
0
1
0
1
0
1
40ms
STORE
RESET OUT
60ms
30ms TO
40ms
40ms
190ms TO 200ms
MEAS
IN PROGRESS
FIGURE 13. RESET OUT,STORE ANDMEASUREMENT IN
PROGRESS OUTPUTS BETWEEN MEASUREMENTS
TABLE 4. DECIMAL POINT POSITIONS
RANGE
FREQUENCY
PERIOD
FREQUENCY
RATIO
TIME
INTERVAL
UNIT
COUNTER
OSCILLATOR
FREQUENCY
0.01s/1 Cycle
D2
D2
D1
D2
D1
D2
0.1s/10 Cycle
D3
D3
D2
D3
D1
D3
1s/100 Cycle
D4
D4
D3
D4
D1
D4
10s/1K Cycle
D5
D5
D4
D5
D1
D5
External
N/A
N/A
N/A
N/A
N/A
N/A
ICM7226A, ICM7226B
相關PDF資料 |
PDF描述 |
|---|---|
| ICM7226A | 8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226B | 8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226BlPL | 8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226AlJL | LJT 128C 128#22D PIN RECP |
| ICM7228 | 8-Digit, Microprocessor-Compatible, LED Display Decoder Driver(8位數字LED顯示驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICM7226 WAF | 制造商:Intersil Corporation 功能描述: |
| ICM7226/D DIE | 制造商:Harris Corporation 功能描述: |
| ICM7226A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226A_01 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226AIJL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:TIMERS COUNTERS AND DISPLAY DRIVERS |
發布緊急采購，3分鐘左右您將得到回復。