- 您現在的位置：買賣IC網 > PDF目錄383092 > ICM7226A (Intersil Corporation) 8-Digit, Multi-Function, Frequency Counter/Timer PDF資料下載
參數資料
| 型號： | ICM7226A |
| 廠商： | Intersil Corporation |
| 元件分類： | 通用總線功能 |
| 英文描述： | 8-Digit, Multi-Function, Frequency Counter/Timer |
| 中文描述： | 8位數字，多功能，頻率計數器/計時器 |
| 文件頁數： | 12/19頁 |
| 文件大?。?/td> | 173K |
| 代理商： | ICM7226A |
9-26
Display Considerations
The display is multiplexed at a 500Hz rate with a digit time of
244
μ
s. An interdigit blanking time of 6
μ
s is used to prevent
display ghosting (faint display of data from previous digit
superimposed on the next digit). Leading zero blanking is
provided, which blanks the left hand zeroes after decimal
point or any non zero digits. Digits to the right of the decimal
point are always displayed. The leading zero blanking will be
disabled when the Main Counter overflows.
The lCM7226A is designed to drive common anode LED dis-
plays at peak current of 25mA/segment, using displays with
V
F
= 1.8V at 25mA. The average DC current will be greater
than 3mA under these conditions. The lCM7226B is designed
to drive common cathode displays at peak current of
15mA/segment using displays with V
F
= 1.8V at 15mA. Resis-
tors can be added in series with the segment drivers to limit
the display current, if required. The Typical Performance
Curves show the digit and segment currents as a function of
output voltage for common anode and common cathode
drivers.
To increase the light output from the displays, V
DD
may be
increased to 6.0V. However, care should be taken to see that
maximum power and current ratings are not exceeded.
The SEGment and Digit outputs in both the ICM7226A and
ICM7226B are not directly compatible with either TTL or
CMOS logic. Therefore, level shifting with discrete transis-
tors may be required to use these outputs as logic signals.
External latching should be down on the leading edge of the
digit signal.
Accuracy
In a Universal Counter, crystal drift and quantization errors
cause errors. In
frequency, period
and
time interval
modes, a signal derived from the oscillator is used in either
the Reference Counter or Main Counter, and in these
modes, an error in the oscillator frequency will cause an
identical error in the measurement. For instance, an oscilla-
tor temperature coefficient of 20ppm/
o
C will cause a mea-
surement error of 20ppm/
o
C.
In addition, there is a quantization error inherent in any digi-
tal measurement of
±
1 count. Clearly this error is reduced by
displaying more digits. In the
frequency
mode maximum
accuracy is obtained with high frequency inputs and in
period
mode maximum accuracy is obtained with low fre-
quency inputs. As can be seen in Figure 16. In
time interval
measurements there can be an error of 1 count per interval.
As a result there is the same inherent accuracy in all ranges
as shown in Figure 17. In
frequency ratio
measurement
can be more accurately obtained by averaging over more
cycles of INPUT B as shown in Figure 18.
FIGURE 16. MAXIMUM ACCURACY OF FREQUENCY AND
PERIOD MEASUREMENTS DUE TO LIMITATIONS
OF QUANTIZATION ERRORS
FIGURE 17. MAXIMUM ACCURACY OF TIME INTERVAL
MEASUREMENT DUE TO LIMITATIONS OF
QUANTIZATION ERRORS
FIGURE 18. MAXIMUM ACCURACY FOR FREQUENCY RATIO MEASUREMENT DUE TO LIMITATION OF QUANTIZATION ERRORS
FREQUENCY MEASURE
0
2
4
8
1
10
10
3
10
7
FREQUENCY (Hz)
M
6
0.01s
0.1s
S
10
5
10s
1s
PERIOD MEASURE
f
OSC
= 10MHz
1 CYCLE
10 CYCLES
10
2
CYCLES
10
3
CYCLES
MAXIMUM TIME INTERVAL
FOR 10
3
INTERVALS
MAXIMUM TIME
INTERVAL FOR
10
INTERVALS
MAXIMUM TIME INTERVAL
FOR 10 INTERVALS
10
3
TIME INTERVAL (
μ
s)
10
4
10
5
10
6
10
7
10
8
10
2
10
1
0
1
2
3
4
5
6
7
8
M
S
1 CYCLE
10 CYCLES
10
2
CYCLES
10
3
CYCLES
RANGE
10
3
10
4
f
A
/f
B
10
5
10
6
10
7
10
8
10
2
10
1
0
1
2
3
4
5
6
7
8
M
S
ICM7226A, ICM7226B
相關PDF資料 |
PDF描述 |
|---|---|
| ICM7226B | 8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226BlPL | 8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226AlJL | LJT 128C 128#22D PIN RECP |
| ICM7228 | 8-Digit, Microprocessor-Compatible, LED Display Decoder Driver(8位數字LED顯示驅動器) |
| ICM7240IJE | Fixed And Programmable Timer/Counters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICM7226A_01 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226AIJL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:TIMERS COUNTERS AND DISPLAY DRIVERS |
| ICM7226ALJL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:8-Digit, Multi-Function, Frequency Counter/Timer |
| ICM7226BIPL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:TIMERS COUNTERS AND DISPLAY DRIVERS |
發布緊急采購，3分鐘左右您將得到回復。