參數資料
型號： ICM7228
廠商： Intersil Corporation
英文描述： 8-Digit, Microprocessor-Compatible, LED Display Decoder Driver(8位數字LED顯示驅動器)
中文描述： 8位、復用輸出、LED解碼驅動器
文件頁數： 13/18頁
文件大?。?/td> 302K
代理商： ICM7228
13
ICM7228
entered when in the shutdown mode. Data is retained in
memory even with the supply voltage as low as 2V.
The ICM7228A/B is shutdown by writing a control word with
Shutdown (lD4) low. The ICM7228C is put into shutdown
mode by driving pin 9, HEXA/CODE B/SHUTDOWN, low.
The ICM7228 operating current with the display blanked is
within 100
μ
A - 200
μ
A for all versions. All versions of the
ICM7228 can be blanked by writing Hex FF to all digits and
selecting Code B format. The ICM7228A and ICM7228B can
also be blanked by selecting No Decode mode and writing
Hex 80 to all digits (See Tables 5and 6).
Common Anode Display Drivers, ICM7228A and
ICM7228C
The common anode digit and segment driver output
schematics are shown in Figure 12. The common anode digit
driver output impedance is approximately 4
. This provides a
nearly constant voltage to the display digits. Each digit has a
minimum of 200mA drive capability. The N-Channel segment
driver’s output impedance of 50
limits the segment current to
approximately 25mA peak current per segment. Both the
segment and digit outputs can directly drive the display,
current limiting resistors are not required.
Individual segment current is not significantly affected by
whether other segments are on or off. This is because the
segment driver output impedance is much higher than that of
the digit driver. This feature is important in bar graph
applications where each bar graph element should have the
same brightness, independent of the number of elements being
turned on.
Common Cathode Display Driver, ICM7228B
The common cathode digit and segment driver output
schematics are shown in Figure 13. The N-channel digit
drivers have an output impedance of approximately 15
.
Each digit has a minimum of 50mA drive capability. The
segment drivers have an output impedance of approximately
100
with typically 10mA peak current drive for each
segment. The common cathode display driver output
currents are only
1
/
4
of the common anode display driver
currents. Therefore, the ICM7228A and ICM7228C common
anode display drivers are recommended for those
applications where high display brightness is desired. The
ICM7228B common cathode display driver is suitable for
driving bubble-lensed monolithic 7 segment displays. They
can also drive individual LED displays up to 0.3 inches in
height when high brightness is not required.
Display Multiplexing
Each digit of the ICM7228 is on for approximately 320
μ
s,
with a multiplexing frequency of approximately 390Hz. The
ICM7228 display drivers provide interdigit blanking. This
ensures that the segment information of the previous digit is
gone and the information of the next digit is stable before the
next digit is driven on. This is necessary to eliminate display
ghosting (a faint display of data from previous digit
superimposed on the next digit). The interdigit blanking time
is 10
μ
s typical with a guaranteed 2
μ
s minimum. The
ICM7228 turns off both the digit drivers and the segment
drivers during the interdigit blanking period. The digit
multiplexing sequence is: D2, D5, D1, D7, D8, D6, D4 and
D3. A typical digit’s drive pulses are shown on Figure 4.
Due to the display multiplexing, the driving duty cycle for
each digit is 12% (100 x
1
/
8
) This means the average current
for each segment is
1
/
8
of its peak current. This must be
considered while designing and selecting the displays.
Driving Larger Displays
If very high display brightness is desired, the ICM7228
display driver outputs can be externally buffered. Figures 14
thru 16 show how to drive either common anode or common
cathode displays using the ICM7228 and external driver
circuit for higher current displays.
Another method of increasing display currents is to connect
two digit outputs together and load the same data into both
digits. This drives the display with the same peak current,
but the average current doubles because each digit of the
display is on for twice as long, i.e.,
1
/
4
duty cycle versus
1
/
8
.
DIGIT
STROBE
INTERDIGIT
BLANKING
SHUTDOWN
V
DD
≈
200mA
COMMON
ANODE
DIGIT
OUTPUT
≈
2k
N
V
SS
P
≈
2k
N
V
SS
N
N
NOTE: When SHUTDOWN goes low INTERDIGIT BLANKING also
stays low.
FIGURE 12A. DIGIT DRIVER
相關PDF資料
PDF描述
ICM7240IJE Fixed And Programmable Timer/Counters
ICM7250IJE Fixed And Programmable Timer/Counters
ICM7260IJE Fixed And Programmable Timer/Counters
ICM7240IPE Fixed And Programmable Timer/Counters
ICM7250IPE Fixed And Programmable Timer/Counters
相關代理商/技術參數
參數描述
ICM7228_05 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:8-Digit, Microprocessor-Compatible, LED Display Decoder Driver
ICM7228AIBI 功能描述:LED顯示驅動器 DISPLAY 8 DIG LED DRIVER 28CDIP IND RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube
ICM7228AIBIZ 功能描述:LED顯示驅動器 DISPLAY 8 DIG LED DRVR 28W IND RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube
ICM7228AIJI 制造商:Maxim Integrated Products 功能描述:8 DIGIT LED DISPLAY DRIVER - Bulk
ICM7228AIJI+ 制造商:Maxim Integrated Products 功能描述:LED DRVR 64SEGMENT 2.5V/3.3V/5V 28CDIP - Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*