- 您現在的位置：買賣IC網 > PDF目錄9019 > ICS276PGILFT (IDT, Integrated Device Technology Inc)VCXO CLK SYNTH TRPL PLL 16-TSSOP PDF資料下載
參數資料
| 型號： | ICS276PGILFT |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 4/10頁 |
| 文件大小： | 0K |
| 描述： | VCXO CLK SYNTH TRPL PLL 16-TSSOP |
| 標準包裝： | 2,500 |
| 系列： | VersaClock™ |
| 類型： | 時鐘/頻率合成器，扇出緩沖器（分配） |
| PLL： | 帶旁路 |
| 輸入： | 晶體 |
| 輸出： | CMOS |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:3 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 200MHz |
| 除法器/乘法器： | 是/是 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 276PGILFT |
ICS276
TRIPLE PLL FIELD PROGRAMMABLE VCXO CLOCK SYNTHESIZER
EPROM AND VCXO SYNTHESIZER
IDT / ICS TRIPLE PLL FIELD PROGRAMMABLE VCXO CLOCK SYNTHESIZER 3
ICS276
REV E 051310
External Components
The ICS276 requires a minimum number of external
components for proper operation.
Series Termination Resistor
Clock output traces over one inch should use series
termination. To series terminate a 50
trace (a commonly
used trace impedance), place a 33
resistor in series with
the clock line, as close to the clock output pin as possible.
The nominal impedance of the clock output is 20
.
Decoupling Capacitors
As with any high-performance mixed-signal IC, the ICS276
must be isolated from system power supply noise to perform
optimally.
Decoupling capacitors of 0.01F must be connected
between each VDD and the PCB ground plane. For
optimum device performance, the decoupling capacitor
should be mounted on the component side of the PCB.
Avoid the use of vias on the decoupling circuit.
Quartz Crystal
The ICS276 VCXO function consists of the external crystal
and the integrated VCXO oscillator circuit. To assure the
best system performance (frequency pull range) and
reliability, a crystal device with the recommended
parameters (shown below) must be used, and the layout
guidelines discussed in the following section shown must be
followed.
The frequency of oscillation of a quartz crystal is determined
by its “cut” and by the load capacitors connected to it. The
ICS276 incorporates on-chip variable load capacitors that
“pull” (change) the frequency of the crystal. The crystal
specified for use with the ICS276 is designed to have zero
frequency error when the total of on-chip + stray
capacitance is 14 pF.
Recommended Crystal Parameters:
Initial Accuracy at 25
° C
±20 ppm
Temperature Stability
±30 ppm
Aging
±20 ppm
Load Capacitance
14 pf
Shunt Capacitance, C0
7 pF Max
C0/C1 Ratio
250 Max
Equivalent Series Resistance
35
Max
The external crystal must be connected as close to the chip
as possible and should be on the same side of the PCB as
the ICS276. There should be no via’s between the crystal
pins and the X1 and X2 device pins. There should be no
signal traces underneath or close to the crystal. See
application note MAN05.
Crystal Tuning Load Capacitors
The crystal traces should include pads for small fixed
capacitors, one between X1 and ground, and another
between X2 and ground. Stuffing of these capacitors on the
PCB is optional. The need for these capacitors is
determined at system prototype evaluation, and is
influenced by the particular crystal used (manufacture and
frequency) and by PCB layout. The typical required
capacitor value is 1 to 4 pF.
To determine the need for and value of the crystal
adjustment capacitors, you will need a PC board of your final
layout, a frequency counter capable of about 1 ppm
resolution and accuracy, two power supplies, and some
samples of the crystals which you plan to use in production,
along with measured initial accuracy for each crystal at the
specified crystal load capacitance, CL.
To determine the value of the crystal capacitors:
1. Connect VDD of the ICS276 to 3.3 V. Connect pin 1 of the
ICS276 to the second power supply. Adjust the voltage on
pin 1 to 0V. Measure and record the frequency of the CLK
output.
2. Adjust the voltage on pin 1 to 3.3 V. Measure and record
the frequency of the same output.
To calculate the centering error:
Where:
ftarget = nominal crystal frequency
Error
10
6
x
f
3.0V
f
tet
arg
–
() f
0V
f
tet
arg
–
()
+
f
tet
arg
-----------------------------------------------------------------------
error
xtal
–
=
相關PDF資料 |
PDF描述 |
|---|---|
| VI-J5K-MZ-F3 | CONVERTER MOD DC/DC 40V 25W |
| VI-J5K-MZ-F2 | CONVERTER MOD DC/DC 40V 25W |
| VI-J5K-MZ-F1 | CONVERTER MOD DC/DC 40V 25W |
| VI-J5J-MZ-F4 | CONVERTER MOD DC/DC 36V 25W |
| VI-J5J-MZ-F3 | CONVERTER MOD DC/DC 36V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS276PGIT | 功能描述:VCXO CLK SYNTH TRPL PLL 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:VersaClock™ 產品變化通告:Product Discontinuation 04/May/2011 標準包裝:96 系列:- 類型:時鐘倍頻器，零延遲緩沖器 PLL:帶旁路 輸入:LVTTL 輸出:LVTTL 電路數:1 比率 - 輸入:輸出:1:8 差分 - 輸入:輸出:無/無 頻率 - 最大:133.3MHz 除法器/乘法器:是/無 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:管件 其它名稱:23S08-5HPGG |
| ICS276PGLF | 功能描述:VCXO CLK SYNTH TRPL PLL 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:VersaClock™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
| ICS276PGLFT | 功能描述:VCXO CLK SYNTH TRPL PLL 16-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:VersaClock™ 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
| ICS276PGT | 功能描述:VCXO CLK SYNTH TRPL PLL 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:VersaClock™ 產品變化通告:Product Discontinuation 04/May/2011 標準包裝:96 系列:- 類型:時鐘倍頻器，零延遲緩沖器 PLL:帶旁路 輸入:LVTTL 輸出:LVTTL 電路數:1 比率 - 輸入:輸出:1:8 差分 - 輸入:輸出:無/無 頻率 - 最大:133.3MHz 除法器/乘法器:是/無 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:管件 其它名稱:23S08-5HPGG |
| ICS280 | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:Package Outline and Package Dimensions (16-pin TSSOP,173 Mil. Body) |
發布緊急采購，3分鐘左右您將得到回復。