2C component. It can read back the data stored" />
參數資料
型號: ICS9250BF-28T
廠商: IDT, Integrated Device Technology Inc
文件頁數: 7/17頁
文件大?。?/td> 0K
描述: IC FREQ GENERATOR/BUFFER 56-SSOP
標準包裝: 1,000
類型: 時鐘/頻率發生器
PLL:
主要目的: Intel CPU 服務器
輸入: 晶體
輸出: 時鐘
電路數: 1
比率 - 輸入:輸出: 1:24
差分 - 輸入:輸出: 無/無
頻率 - 最大: 133.3MHz
電源電壓: 3.135 V ~ 3.465 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 56-BSSOP(0.295",7.50mm 寬)
供應商設備封裝: 56-SSOP
包裝: 帶卷 (TR)
其它名稱: 9250BF-28T
15
ICS9250-28
1.
The ICS clock generator is a slave/receiver, I
2C component. It can read back the data stored in the latches for
verification. Read-Back will support Intel PIIX4 "Block-Read" protocol.
2.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
3.
The input is operating at 3.3V logic levels.
4.
The data byte format is 8 bit bytes.
5.
To simplify the clock generator I
2C interface, the protocol is set to use only "Block-Writes" from the controller. The
bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete byte
has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored for those
two bytes. The data is loaded until a Stop sequence is issued.
6.
At power-on, all registers are set to a default condition, as shown.
General I
2C serial interface information
The information in this section assumes familiarity with I
2C programming.
For more information, contact ICS for an I
2C programming application note.
How to Write:
Controller (host) sends a start bit.
Controller (host) sends the write address D2
(H)
ICS clock will acknowledge
Controller (host) sends a dummy command code
ICS clock will acknowledge
Controller (host) sends a dummy byte count
ICS clock will acknowledge
Controller (host) starts sending first byte (Byte 0)
through byte 5
ICS clock will acknowledge each byte one at a time.
Controller (host) sends a Stop bit
How to Read:
Controller (host) will send start bit.
Controller (host) sends the read address D3
(H)
ICS clock will acknowledge
ICS clock will send the byte count
Controller (host) acknowledges
ICS clock sends first byte (Byte 0) through byte 5
Controller (host) will need to acknowledge each byte
Controller (host) will send a stop bit
Notes:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D3(H)
ACK
Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Stop Bit
How to Read:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D2(H)
ACK
Dummy Command Code
ACK
Dummy Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Stop Bit
How to Write:
相關PDF資料
PDF描述
SL28647BLCT IC CLOCK CK505 DIFF PAIR 72QFN
IDTQS3125QG IC BUS SWITCH QUAD 16QSOP
SL28647CLC IC CLOCK CK505 DIFF PAIR 72QFN
SL28647BLC IC CLOCK CK505 DIFF PAIR 72QFN
CY28547LFXC IC CLOCK CK505/410M INTEL 72QFN
相關代理商/技術參數
參數描述
ICS9250BFI-27LF 制造商:Integrated Device Technology Inc 功能描述:IC PLL FREQ GEN 56-SSOP
ICS9250BFI-27LFT 制造商:Integrated Device Technology Inc 功能描述:IC PLL FREQ GEN 56-SSOP
ICS9250CF-10 功能描述:IC FREQ TIMING GENERATOR 56-SSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP(0.209",5.30mm 寬) 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT
ICS9250CF-10LF 功能描述:IC FREQ TIMING GENERATOR 56-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP(0.209",5.30mm 寬) 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT
ICS9250CF-10LFT 功能描述:IC TIMING GENERATOR 56-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP (0.240",6.10mm 寬) 供應商設備封裝:64-TSSOP 包裝:管件