- 您現在的位置：買賣IC網 > PDF目錄9604 > ICS9250CF-10T (IDT, Integrated Device Technology Inc)IC FREQ TIMING GENERATOR 56-SSOP PDF資料下載
參數資料
| 型號： | ICS9250CF-10T |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FREQ TIMING GENERATOR 56-SSOP |
| 標準包裝： | 1,000 |
| 類型： | 時鐘/頻率發生器 |
| PLL： | 是 |
| 主要目的： | Intel CPU 服務器 |
| 輸入： | 晶體 |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:27 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 133MHz |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-BSSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 56-SSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 9250CF-10T |
5
ICS9250- 10
1.
The ICS clock generator is a slave/receiver, I2C component. It can read back the data stored in the latches for verification.
Read-BackwillsupportIntelPIIX4"Block-Read"protocol.
2.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
3.
The input is operating at 3.3V logic levels.
4.
The data byte format is 8 bit bytes.
5.
To simplify the clock generator I2C interface, the protocol is set to use only "Block-Writes" from the controller. The
bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete byte
has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored for those
two bytes. The data is loaded until a Stop sequence is issued.
6.
At power-on, all registers are set to a default condition, as shown.
General I
2C serial interface information
The information in this section assumes familiarity with I2C programming.
For more information, contact ICS for an I2C programming application note.
How to Write:
Controller (host) sends a start bit.
Controller (host) sends the write address D2
(H)
ICS clock will acknowledge
Controller (host) sends a dummy command code
ICS clock will acknowledge
Controller (host) sends a dummy byte count
ICS clock will acknowledge
Controller (host) starts sending first byte (Byte 0)
through byte 5
ICS clock will acknowledge each byte one at a time.
Controller (host) sends a Stop bit
How to Read:
Controller (host) will send start bit.
Controler (host) sends the read address D3
(H)
ICS clock will acknowledge
ICS clock will send the byte count
Controller (host) acknowledges
ICS clock sends first byte (Byte 0) through byte 5
Controller (host) will need to acknowledge each byte
Controller (host) will send a stop bit
Notes:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D3(H)
ACK
Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Stop Bit
How to Read:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D2(H)
ACK
Dummy Command Code
ACK
Dummy Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Stop Bit
How to Write:
相關PDF資料 |
PDF描述 |
|---|---|
| ICS9250CF-10LFT | IC TIMING GENERATOR 56-SSOP |
| D38999/26ME26JN | CONN PLUG 26POS STRAIGHT W/SCKT |
| ICL3232IB | IC 2DRVR/2RCVR RS232 3V 16-SOIC |
| VI-J6T-MX-F1 | CONVERTER MOD DC/DC 6.5V 75W |
| MS27473E24A4S | CONN PLUG 56POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS9250CF-22T | 制造商:INT_CIR_SYS 功能描述: |
| ICS9250F-19 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| ICS9250F-26 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| ICS9250F-28 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| ICS9250F-28-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
發布緊急采購，3分鐘左右您將得到回復。