2C component. It can read back th" />
參數資料
型號: ICS93716AGLFT
廠商: IDT, Integrated Device Technology Inc
文件頁數: 2/13頁
文件大?。?/td> 0K
描述: IC DDR PLL CLOCK DRIVER 28-TSSOP
標準包裝: 1,000
類型: 時鐘緩沖器/驅動器
PLL:
主要目的: 存儲器,DDR
輸入: 時鐘
輸出: 時鐘
電路數: 1
比率 - 輸入:輸出: 2:6
差分 - 輸入:輸出: 無/是
頻率 - 最大: 233MHz
電源電壓: 2.3 V ~ 2.7 V
工作溫度: 0°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 28-TSSOP(0.240",6.10mm 寬)
供應商設備封裝: 28-TSSOP
包裝: 帶卷 (TR)
其它名稱: 93716AGLFT
10
ICS93716
0420H—09/10/08
1.
The ICS clock generator is a slave/receiver, I
2C component. It can read back the data stored in the latches for
verification. Read-Back will support Intel PIIX4 "Block-Read" protocol.
2.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
3.
The input is operating at 3.3V logic levels.
4.
The data byte format is 8 bit bytes.
5.
To simplify the clock generator I
2C interface, the protocol is set to use only "Block-Writes" from the controller.
The bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any
complete byte has been transferred. The Command code and Byte count shown above must be sent, but the
data is ignored for those two bytes. The data is loaded until a Stop sequence is issued.
6.
At power-on, all registers are set to a default condition, as shown.
General I
2C serial interface information
The information in this section assumes familiarity with I
2C programming.
For more information, contact ICS for an I
2C programming application note.
How to Write:
Controller (host) sends a start bit.
Controller (host) sends the write address D2
(H)
ICS clock will acknowledge
Controller (host) sends a dummy command code
ICS clock will acknowledge
Controller (host) sends a dummy byte count
ICS clock will acknowledge
Controller (host) starts sending first byte (Byte 0)
through byte 5
ICS clock will acknowledge each byte one at a time.
Controller (host) sends a Stop bit
How to Read:
Controller (host) will send start bit.
Controller (host) sends the read address D3
(H)
ICS clock will acknowledge
ICS clock will send the byte count
Controller (host) acknowledges
ICS clock sends first byte (Byte 0) through byte 5
Controller (host) will need to acknowledge each byte
Controller (host) will send a stop bit
Notes:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D3(H)
ACK
Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Stop Bit
How to Read:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D2(H)
ACK
Dummy Command Code
ACK
Dummy Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Stop Bit
How to Write:
相關PDF資料
PDF描述
D38999/26MH55HN CONN PLUG 55POS STRAIGHT W/PINS
MS3124P14-18P CONN RCPT 18POS JAM NUT W/PINS
SL28504BZC-1T IC CLOCK GEN EAGLELAKE 56TSSOP
ISL8489EIB TRANSCEIVER RS485/522 ESD 14SOIC
VI-B1N-IU CONVERTER MOD DC/DC 18.5V 200W
相關代理商/技術參數
參數描述
ICS93716AGT 功能描述:IC DDR PLL CLOCK DRIVER 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP(0.209",5.30mm 寬) 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT
ICS93716BFLF 制造商:Integrated Device Technology Inc 功能描述:IC CLK BUF DDR 233MHZ 1CIRC
ICS93716BFLFT 制造商:Integrated Device Technology Inc 功能描述:IC CLK BUF DDR 233MHZ 1CIRC
ICS93716BGLF 功能描述:IC DDR PLL CLOCK DRIVER 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP(0.209",5.30mm 寬) 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT
ICS93716BGLFT 功能描述:IC DDR PLL CLOCK DRIVER 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP(0.209",5.30mm 寬) 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT