參數資料
型號: ICX086AL
廠商: Sony Corporation
英文描述: 1/4-Inch CCD Image Sensor For EIA B/W Video Cameras(1/4 英寸CCD圖像傳感器(用于EIA黑白攝像機))
中文描述: 4英寸CCD的環境影響評估乙圖像傳感器/ W視頻相機(1 / 4英寸防治荒漠化公約圖像傳感器(用于評估黑白攝像機))
文件頁數: 9/17頁
文件大?。?/td> 213K
代理商: ICX086AL
– 9 –
ICX086AL
Image Sensor Characteristics Measurement Method
Measurement conditions
1) In the following measurements, the device drive conditions are at the typical values of the bias and clock
voltage conditions.
2) In the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical
black (OB) level is used as the reference for the signal output, and the value measured at point [
A] in the
drive circuit example is used.
Definition of standard imaging conditions
1) Standard imaging condition
I
:
Use a pattern box (luminance: 706cd/m
2
, color temperature of 3200K halogen source) as a subject.
(Pattern for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut
filter and image at F8. The luminous intensity to the sensor receiving surface at this point is defined as the
standard sensitivity testing luminous intensity.
2) Standard imaging condition
II
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted
to the value indicated in each testing item by the lens diaphragm.
1. Sensitivity
Set to standard imaging condition
I
. After selecting the electronic shutter mode with a shutter speed of
1/250s, measure the signal output (Vs) at the center of the screen and substitute the value into the
following formula.
2. Saturation signal
Set to standard imaging condition
II
. After adjusting the luminous intensity to 10 times the intensity with the
average value of the signal output, 200mV, measure the minimum value of the signal output.
3. Smear
Set to standard imaging condition
II
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity to
500 times the intensity with the average value of the signal output, 200mV. When the readout clock is
stopped and the charge drain is executed by the electronic shutter at the respective H blankings, measure
the maximum value (VSm [mV]) of the signal output and substitute the value into the following formula.
4. Video signal shading
Set to standard imaging condition
II
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity so
that the average value of the signal output is 200mV. Then measure the maximum (Vmax [mV]) and
minimum (Vmin [mV]) values of the signal output and substitute the values into the following formula.
SH = (Vmax – Vmin)/200
×
100 [%]
Sm =
×
100 [%] (1/10V method conversion value)
×
200
VSm
500
1
10
1
S = Vs
×
[mV]
60
250
×
相關PDF資料
PDF描述
ICX087AKB Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras
ICX087AK Diagonal 4.5mm (Type 1/4) CCD Image Sensor For PAL Color Video Cameras(對角線式、4.5毫米(1/4型)CCD圖像傳感器(用于PAL制式彩色攝像機))
ICX087AL 1/4-Inch CCD Image Sensor For CCIR B/W Video Cameras(1/4 英寸CCD圖像傳感器(用于CCIR黑白攝像機))
ICX088AK Diagonal 4.5mm (Type 1/4) CCD Image Sensor for NTSC Color Video Cameras
ICX089AK Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras
相關代理商/技術參數
參數描述
ICX087AK 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras
ICX087AKB 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras
ICX087AL 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for CCIR B/W Video Cameras
ICX088AK 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for NTSC Color Video Cameras
ICX089AK 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras