參數資料
型號: IDT7006L15PF
廠商: INTEGRATED DEVICE TECHNOLOGY INC
元件分類: DRAM
英文描述: Wide Input Voltage PWM/PFM Controller
中文描述: 16K X 8 DUAL-PORT SRAM, 15 ns, PQFP64
封裝: 14 X 14 MM, 1.40 MM HEIGHT, TQFP-64
文件頁數: 16/20頁
文件大小: 263K
代理商: IDT7006L15PF
6.07
16
IDT7006S/L
HIGH-SPEED 16K x 8 DUAL-PORT STATIC RAM
MILITARY AND COMMERCIAL TEMPERATURE RANGES
TRUTH TABLE II —
ADDRESS BUSY ARBITRATION
Inputs
A
0L
-A
13L
CE
L
CE
R
A
0R
-A
13R
X
X
NO MATCH
H
X
MATCH
X
H
MATCH
L
L
MATCH
Outputs
BUSY
L(1)
H
H
H
(2)
BUSY
R(1)
H
H
H
(2)
Function
Normal
Normal
Normal
Write Inhibit
(3)
NOTES:
1. Pins
BUSY
L
and
BUSY
R
are both outputs when the part is configured as a master. Both are inputs when configured as a slave.
BUSY
X
outputs on the
IDT7006 are push pull, not open drain outputs. On slaves the
BUSY
X
input internally inhibits writes.
2. "L" if the inputs to the opposite port were stable prior to the address and enable inputs of this port. "H" if the inputs to the opposite port became stable
after the address and enable inputs of this port. If t
APS
is not met, either
BUSY
L
or
BUSY
R
= Low will result.
BUSY
L
and
BUSY
R
outputs cannot be low
simultaneously.
3. Writes to the left port are internally ignored when
BUSY
L
outputs are driving low regardless of actual logic level on the pin. Writes to the right port are
internally ignored when
BUSY
R
outputs are driving low regardless of actual logic level on the pin.
2739 tbl 18
TRUTH TABLE III — EXAMPLE OF SEMAPHORE PROCUREMENT SEQUENCE
(1,2)
Functions
D
0
- D
7
Left
No Action
1
Left Port Writes "0" to Semaphore
0
Right Port Writes "0" to Semaphore
0
Left Port Writes "1" to Semaphore
1
Left Port Writes "0" to Semaphore
1
Right Port Writes "1" to Semaphore
0
Left Port Writes "1" to Semaphore
1
Right Port Writes "0" to Semaphore
1
Right Port Writes "1" to Semaphore
1
Left Port Writes "0" to Semaphore
0
Left Port Writes "1" to Semaphore
1
D
0
- D
7
Right
Status
1
1
1
0
0
1
1
0
1
1
1
Semaphore free
Left port has semaphore token
No change. Right side has no write access to semaphore
Right port obtains semaphore token
No change. Left port has no write access to semaphore
Left port obtains semaphore token
Semaphore free
Right port has semaphore token
Semaphore free
Left port has semaphore token
Semaphore free
NOTES:
1. This table denotes a sequence of events for only one of the eight semaphores on the IDT7006.
2. There are eight semaphore flags written to via I/O
0
and read from all I/O's (I/O
0
-I/O
7
). These eight semaphores are addressed by A
0
- A
2
.
2739 tbl 19
writes to memory location 3FFF (HEX) and to clear the
interrupt flag (
INT
R
), the right port must read the memory
location 3FFF. The message (8 bits) at 3FFE or 3FFF is user-
defined, since it is an addressable SRAM location. If the
interrupt function is not used, address locations 3FFE and
3FFF are not used as mail boxes, but as part of the random
access memory. Refer to Truth Table for the interrupt opera-
tion.
BUSY LOGIC
Busy Logic provides a hardware indication that both ports
of the RAM have accessed the same location at the same
time. It also allows one of the two accesses to proceed and
signals the other side that the RAM is “Busy”. The busy pin can
then be used to stall the access until the operation on the other
side is completed. If a write operation has been attempted
from the side that receives a busy indication, the write signal
is gated internally to prevent the write from proceeding.
The use of busy logic is not required or desirable for all
FUNCTIONAL DESCRIPTION
The IDT7006 provides two ports with separate control,
address and I/O pins that permit independent access for reads
or writes to any location in memory. The IDT7006 has an
automatic power down feature controlled by
CE
. The
CE
controls on-chip power down circuitry that permits the
respective port to go into a standby mode when not selected
(
CE
high). When a port is enabled, access to the entire
memory array is permitted.
INTERRUPTS
If the user chooses to use the interrupt function, a memory
location (mail box or message center) is assigned to each port.
The left port interrupt flag (
INT
L
) is asserted when the right port
writes to memory location 3FFE (HEX) where a write is
defined as
CE
= R/
W
= V
IL
per the Truth Table
. The left port
clears the interrupt by reading address location 3FFE access
when CE
R
= OE
R
= V
IL,
R/
W
is a "don't care". Likewise, the
right port interrupt flag (
INT
R
) is asserted when the left port
相關PDF資料
PDF描述
IDT7006L15PFB Wide Input Voltage PWM/PFM Controller; Package: QSOP; No of Pins: 16; Container: Rail
IDT7006L17F Wide Input Voltage PWM/PFM Controller; Package: QSOP; No of Pins: 16; Container: Tape & Reel
IDT7006L17FB Wide Input Voltage PWM/PFM Controller
IDT7006L17G Wide Input Voltage Dual-Output/DDR PWM/PFM Controller; Package: TSSOP; No of Pins: 28; Container: Rail
IDT7006L17GB Wide Input Voltage Dual-Output/DDR PWM/PFM Controller
相關代理商/技術參數
參數描述
IDT7006L15PF8 功能描述:IC SRAM 128KBIT 15NS 64TQFP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:45 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 雙端口,異步 存儲容量:128K(8K x 16) 速度:15ns 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:100-LQFP 供應商設備封裝:100-TQFP(14x14) 包裝:托盤 其它名稱:70V25S15PF
IDT7006L15PFB 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:HIGH-SPEED 16K x 8 DUAL-PORT STATIC RAM
IDT7006L15PFG 功能描述:IC SRAM 128KBIT 15NS 64TQFP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 雙端口,同步 存儲容量:1.125M(32K x 36) 速度:5ns 接口:并聯 電源電壓:3.15 V ~ 3.45 V 工作溫度:-40°C ~ 85°C 封裝/外殼:256-LBGA 供應商設備封裝:256-CABGA(17x17) 包裝:帶卷 (TR) 其它名稱:70V3579S5BCI8
IDT7006L15PFG8 功能描述:IC SRAM 128KBIT 15NS 64TQFP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:45 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 雙端口,異步 存儲容量:128K(8K x 16) 速度:15ns 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:100-LQFP 供應商設備封裝:100-TQFP(14x14) 包裝:托盤 其它名稱:70V25S15PF
IDT7006L17F 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:HIGH-SPEED 16K x 8 DUAL-PORT STATIC RAM