- 您現在的位置：買賣IC網 > PDF目錄353712 > IL300-X009 (Vishay Intertechnology,Inc.) Linear Optocoupler, High Gain Stability, Wide Bandwidth PDF資料下載
參數資料
| 型號： | IL300-X009 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Linear Optocoupler, High Gain Stability, Wide Bandwidth |
| 中文描述： | 線性光耦，高增益的穩定性，寬帶 |
| 文件頁數： | 8/15頁 |
| 文件大小： | 196K |
| 代理商： | IL300-X009 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
www.vishay.com
2
Document Number 83622
Rev. 1.4, 26-Oct-04
VISHAY
IL300
Vishay Semiconductors
Operation Description
A typical application circuit (Figure 1) uses an opera-
tional amplifier at the circuit input to drive the LED.
The feedback photodiode sources current to R1 con-
nected to the inverting input of U1. The photocurrent,
IP1, will be of a magnitude to satisfy the relationship of
(IP1 = VIN/R1).
The magnitude of this current is directly proportional
to the feedback transfer gain (K1) times the LED drive
current ( VIN/R1 = K1 IF). The op-amp will supply
LED current to force sufficient photocurrent to keep
the node voltage (Vb) equal to Va.
The output photodiode is connected to a non-invert-
ing voltage follower amplifier. The photodiode load
resistor, R2, performs the current to voltage conver-
sion. The output amplifier voltage is the product of the
output forward gain (K2) times the LED current and
photodiode load, R2 ( VO = IF K2 R2).
Therefore, the overall transfer gain (VO/VIN) becomes
the ratio of the product of the output forward gain (K2)
times the photodiode load resistor (R2) to the product
of the feedback transfer gain (K1) times the input
resistor (R1). This reduces to
VO/VIN=(K2 R2)/(K1 R1).
The overall transfer gain is completely independent of
the LED forward current. The IL300 transfer gain (K3)
is expressed as the ratio of the output gain (K2) to the
feedback gain (K1). This shows that the circuit gain
becomes the product of the IL300 transfer gain times
the ratio of the output to input resistors
VO/VIN = K3 (R2/R1).
K1-Servo Gain
The ratio of the input photodiode current (IP1) to the
LED current (IF) i.e., K1 = IP1/IF.
K2-Forward Gain
The ratio of the output photodiode current (IP2) to the
LED current (IF), i.e., K2 = IP2/IF.
K3-Transfer Gain
The Transfer Gain is the ratio of the Forward Gain to
the Servo gain, i.e., K3 = K2/K1.
K3-Transfer Gain Linearity
The percent deviation of the Transfer Gain, as a func-
tion of LED or temperature from a specific Transfer
Gain at a fixed
LED current and temperature.
Photodiode
A silicon diode operating as a current source. The out-
put current is proportional to the incident optical flux
supplied by the LED emitter. The diode is operated in
the photovoltaic or photoconductive mode. In the pho-
tovoltaic mode the diode functions as a current
source in parallel with a forward biased silicon diode.
The magnitude of the output current and voltage is
dependent upon the load resistor and the incident
LED optical flux. When operated in the photoconduc-
tive mode the diode is connected to a bias supply
which reverse biases the silicon diode. The magni-
tude of the output current is directly proportional to the
LED incident optical flux.
LED (Light Emitting Diode)
An infrared emitter constructed of AlGaAs that emits
at 890 nm operates efficiently with drive current from
500
A to 40 mA. Best linearity can be obtained at
drive currents between 5.0 mA to 20 mA. Its output
flux typically changes by - 0.5 % /°C over the above
operational current range.
Application Circuit
Figure 1. Typical Application Circuit
iil300_01
8
7
6
5
K1
1
2
3
4
K2
R1
R2
IL300
Vb
Va
+
-
U1
Vin
lp 1
-
U2
+
lp 2
Vout
VCC
IF
Vc
+
相關PDF資料 |
PDF描述 |
|---|---|
| IL300-F | Male Disconnect Solderless Terminal; Wire Size (AWG):22-18; Tab Width:0.187"; Insulator Color:Red; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No RoHS Compliant: No |
| IL300-F-X006 | Linear Optocoupler, High Gain Stability, Wide Bandwidth |
| IL300-F-X007 | Linear Optocoupler, High Gain Stability, Wide Bandwidth |
| IL300-F-X009 | Male Disconnect Solderless Terminal; Wire Size (AWG):22-18; Tab Width:0.250"; Insulator Color:Red RoHS Compliant: Yes |
| IL300-X006 | Linear Optocoupler, High Gain Stability, Wide Bandwidth |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IL300-X009T | 功能描述:高線性光耦合器 Single Linear, High Gain, Wide Bandwidth RoHS:否 制造商:Avago Technologies 輸入類型:AC/DC 最大正向二極管電壓:1.95 V 最大反向二極管電壓:2.5 V 最大輸入二極管電流:25 mA 最大功率耗散:60 mW 最大工作溫度:+ 100 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-8 Gull Wing 封裝:Tube |
| IL300-X016 | 功能描述:高線性光耦合器 Single Linear, High Gain, Wide Bandwidth RoHS:否 制造商:Avago Technologies 輸入類型:AC/DC 最大正向二極管電壓:1.95 V 最大反向二極管電壓:2.5 V 最大輸入二極管電流:25 mA 最大功率耗散:60 mW 最大工作溫度:+ 100 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-8 Gull Wing 封裝:Tube |
| IL300-X017 | 功能描述:高線性光耦合器 Single Linear, High Gain, Wide Bandwidth RoHS:否 制造商:Avago Technologies 輸入類型:AC/DC 最大正向二極管電壓:1.95 V 最大反向二極管電壓:2.5 V 最大輸入二極管電流:25 mA 最大功率耗散:60 mW 最大工作溫度:+ 100 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-8 Gull Wing 封裝:Tube |
| IL3085-1-01 | 功能描述:IL3585-1E IsoLoop? Series Interface, Isolated, CAN Evaluation Board 制造商:nve corp/isolation products 系列:IsoLoop? 零件狀態:有效 主要用途:接口，隔離式，CAN 嵌入式:- 使用的 IC/零件:IL3585-1E 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1 |
| IL3085-1E | 功能描述:RS422, RS485 Digital Isolator 2500Vrms 3 Channel 4Mbps 30kV/μs CMTI 16-SSOP (0.154", 3.90mm Width) 制造商:nve corp/isolation products 系列:IsoLoop? 包裝:管件 零件狀態:有效 技術:GMR（大型磁阻傳感） 類型:RS422，RS485 隔離式電源:無 通道數:3 輸入 - 輸入側 1/輸入側 2:2/1 通道類型:單向 電壓 - 隔離:2500Vrms 共模瞬態抗擾度（最小值）:30kV/μs 數據速率:4Mbps 傳播延遲 tpLH / tpHL（最大值）:150ns，150ns 脈寬失真（最大）:- 上升/下降時間（典型值）:- 電壓 - 電源:3 V ~ 5.5 V，4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SSOP（0.154"，3.90mm 寬） 供應商器件封裝:16-QSOP 標準包裝:100 |
發布緊急采購，3分鐘左右您將得到回復。