- 您現在的位置：買賣IC網 > PDF目錄67717 > IL300-X019 (VISHAY SEMICONDUCTORS) SPECIALTY OPTOELECTRONIC DEVICE PDF資料下載
參數資料
| 型號： | IL300-X019 |
| 廠商： | VISHAY SEMICONDUCTORS |
| 元件分類： | 光電元器件 |
| 英文描述： | SPECIALTY OPTOELECTRONIC DEVICE |
| 封裝： | ROHS COMPLIANT, SMD, 8 PIN |
| 文件頁數： | 15/15頁 |
| 文件大?。?/td> | 176K |
| 代理商： | IL300-X019 |
VISHAY
IL300
Document Number 83622
Rev. 1.5, 24-Mar-05
Vishay Semiconductors
www.vishay.com
9
The isolated amplifier provides the PWM control sig-
nal which is derived from the output supply voltage.
Figure 16 more closely shows the basic function of
the amplifier.
The control amplifier consists of a voltage divider and
a non-inverting unity gain stage. The TDA4918 data
sheet indicates that an input to the control amplifier is
a high quality operational amplifier that typically
requires a +3.0 V signal. Given this information, the
amplifier circuit topology shown in Figure 18 is
selected.
The power supply voltage is scaled by R1 and R2 so
that there is + 3.0 V at the non-inverting input (Va) of
U1. This voltage is offset by the voltage developed by
photocurrent flowing through R3. This photocurrent is
developed by the optical flux
created by current flowing through the LED. Thus as
the scaled monitor voltage (Va) varies it will cause a
change in the LED current necessary to satisfy the dif-
ferential voltage needed across R3 at the inverting
input.
The first step in the design procedure is to select the
value of R3 given the LED quiescent current (IFq) and
the servo gain (K1). For this design, IFq = 12 mA. Fig-
ure 4 shows the servo photocurrent at IFq is found to
be 100
A. With this data R3 can be calculated.
For best input offset compensation at U1, R2 will
equal R3. The value of R1 can easily be calculated
from the following.
The value of R5 depends upon the IL300 Transfer
Gain (K3). K3 is targeted to be a unit gain device,
however to minimize the part to part Transfer Gain
variation, Infineon offers K3 graded into ± 5 % bins.
R5 can determined using the following equation,
Or if a unity gain amplifier is being designed (VMON-
ITOR = VOUT, R1 = 0), the equation simplifies to:
Figure 16. Isolated Control Amplifier
R3 =
Vb
IPI
=
3V
100
A
=30K
17164
iil300_16
+
-
Voltage
Monitor
R1
R2
To Control
Input
ISO
AMP
+1
R1=R2
(
VMONITOR
Va
- 1
)
17165
R5 =
VOUT
VMONITOR
R3(R1 + R2)
R2K3
17166
R5 =
R3
K3
17190
相關PDF資料 |
PDF描述 |
|---|---|
| IL300-E-X017 | SPECIALTY OPTOELECTRONIC DEVICE |
| IL300-F | SPECIALTY OPTOELECTRONIC DEVICE |
| IL300-X007 | SPECIALTY OPTOELECTRONIC DEVICE |
| IL300-DE-X007T | SPECIALTY OPTOELECTRONIC DEVICE |
| IL300-F-X001 | SPECIALTY OPTOELECTRONIC DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IL3085-1-01 | 功能描述:IL3585-1E IsoLoop? Series Interface, Isolated, CAN Evaluation Board 制造商:nve corp/isolation products 系列:IsoLoop? 零件狀態:有效 主要用途:接口，隔離式，CAN 嵌入式:- 使用的 IC/零件:IL3585-1E 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1 |
| IL3085-1E | 功能描述:RS422, RS485 Digital Isolator 2500Vrms 3 Channel 4Mbps 30kV/μs CMTI 16-SSOP (0.154", 3.90mm Width) 制造商:nve corp/isolation products 系列:IsoLoop? 包裝:管件 零件狀態:有效 技術:GMR（大型磁阻傳感） 類型:RS422，RS485 隔離式電源:無 通道數:3 輸入 - 輸入側 1/輸入側 2:2/1 通道類型:單向 電壓 - 隔離:2500Vrms 共模瞬態抗擾度（最小值）:30kV/μs 數據速率:4Mbps 傳播延遲 tpLH / tpHL（最大值）:150ns，150ns 脈寬失真（最大）:- 上升/下降時間（典型值）:- 電壓 - 電源:3 V ~ 5.5 V，4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SSOP（0.154"，3.90mm 寬） 供應商器件封裝:16-QSOP 標準包裝:100 |
| IL3085-3E | 制造商:NVE Corporation 功能描述:IC TRANSCEIVER RS485 16-SOIC |
| IL3085E | 制造商:NVE Corporation 功能描述:IC TRANSCEIVER RS485 16-SOIC |
| IL31 | 功能描述:晶體管輸出光電耦合器 Photodarlington Out Single CTR >200% RoHS:否 制造商:Vishay Semiconductors 輸入類型:DC 最大集電極/發射極電壓:70 V 最大集電極/發射極飽和電壓:0.4 V 絕緣電壓:5300 Vrms 電流傳遞比:100 % to 200 % 最大正向二極管電壓:1.65 V 最大輸入二極管電流:60 mA 最大集電極電流:100 mA 最大功率耗散:100 mW 最大工作溫度:+ 110 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-4 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。