- 您現在的位置：買賣IC網 > PDF目錄1925 > IL3585 (NVE Corp/Isolation Products)ISOLATOR PROFIB 485 XCVR 16SOICW PDF資料下載
參數資料
| 型號： | IL3585 |
| 廠商： | NVE Corp/Isolation Products |
| 文件頁數： | 3/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | ISOLATOR PROFIB 485 XCVR 16SOICW |
| 產品培訓模塊： | IsoLoop® Isolator |
| 標準包裝： | 50 |
| 系列： | IsoLoop® |
| 類型： | 收發器，隔離式 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS485 |
| 電源電壓： | 3.3V，5V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | * |
| 包裝： | 管件 |
| 其它名稱： | 390-1033-5 |
IL3585
11
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
NVE Corporation
Fail-Safe Operation
“Fail-safe operation” is defined here as the forcing of a logic high state on the “R” output in response to an open-circuit condition between the
“A” and “B” lines of the bus, or when no drivers are active on the bus.
Proper biasing can ensure fail-safe operation, that is a known state when there are no active drivers on the bus. IL3000-Series Isolated
Transceivers include internal pull-up and pull-down resistors of approximately 30 k in the receiver section (RFS-INT; see figure below). These
internal resistors are designed to ensure failsafe operation but only if there are no termination resistors. The entire VDD will appear between inputs
“A” and “B” if there is no loading and no termination resistors, and there will be more than the required 200 mV with up to four RS-485 worst-
case Unit Loads of 12 k. Many designs operating below 1 Mbps or less than 1,000 feet are unterminated. Termination resistors may not be
necessary for very low data rates and very short cable runs because reflections have time to settle before data sampling, which occurs at the
middle of the bit interval.
In busses with low-impedance termination resistors however, the differential voltage across the conductor pair will be close to zero with no active
drivers. In this case the state of the bus is indeterminate, and the idle bus will be susceptible to noise. For example, with 120 termination
resistors (RT) on each end of the cable, and four Unit Loads (12 k each), without external fail-safe biasing resistors the internal pull-up and pull-
down resistors will produce a voltage between inputs “A” and “B” of only about 5 mV. This is not nearly enough to ensure a known state.
External fail-safe biasing resistors (RFS-EXT) at one end of the bus can ensure fail-safe operation with a terminated bus. Resistors should be
selected so that under worst-case power supply and resistor tolerances there is at least 200 mV across the conductor pair with no active drivers to
meet the input sensitivity specification of the RS-485 standard.
Using the same value for pull-up and pull-down biasing resistors maintains balance for positive- and negative going transitions. Lower-value
resistors increase inactive noise immunity at the expense of quiescent power consumption. Note that each Unit Load on the bus adds a worst-case
loading of 12 k across the conductor pair, and 32 Unit Loads add 375 worst-case loading. The more loads on the bus, the lower the required
values of the biasing resistors.
In the example with two 120 termination resistors and four Unit Loads, 560 external biasing resistors provide more than 200 mV between
“A” and “B” with adequate margin for power supply variations and resistor tolerances. This ensures a known state when there are no active
drivers. Other illustrative examples are shown in the table below:
Fail-Safe Biasing
R
B
V
DD
30K
GND
A
5 V
R
FS-EXT
R
T
R
T
R
FS-EXT
R
FS-INT
R
FS-INT
Fail-Safe
RT
Loading
Operation?
None
Four unit loads (12 k ea.)
238 mV
Yes
120
Four unit loads (12 k ea.)
5 mV
No
560
120
Four unit loads (12 k ea.)
254 mV
Yes
510
120
32 unit loads (12 k ea.)
247 mV
Yes
Nominal VA-B
(inactive)
RFS-EXT
Internal Only
相關PDF資料 |
PDF描述 |
|---|---|
| IL3685E | PROFIBUS RS-485 INTERFACE ISO |
| IL41050TE | IC TXRX ISOLATED CAN HS 16SOIC |
| IL422-3V | ISOLATOR HS MAGNETC RS422 16SOIC |
| IL485E-3V | ISOLATOR HS MAG DIGITAL 16SOICW |
| IL485W | ISOLATOR HS MAG DIGITAL 16SOICW |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IL3585-01 | 制造商:NVE Corporation 功能描述:ISOLATED RS-485 EVAL BOARD 制造商:NVE Corporation 功能描述:TRANSCEIVER RS485 40MBPS 5V 制造商:NVE Corporation 功能描述:TRANSCEIVER, RS485, 40MBPS, 5V, SOIC-16 制造商:NVE Corporation 功能描述:TRANSCEIVER, RS485, 40MBPS, 5V, SOIC-16; Device Type:Transceiver; IC Interface Type:RS485; No. of Drivers:1; Supply Voltage Min:3V; Supply Voltage Max:5.5V; Driver Case Style:SOIC; No. of Pins:16; Operating Temperature Min:-40C 制造商:NVE Corporation 功能描述:TRANSCEIVER, RS485, 40MBPS, 5V, SOIC-16; Device Type:Transceiver; IC Interface Type:RS485; No. of Drivers:1; Supply Voltage Min:3V; Supply Voltage Max:5.5V; Driver Case Style:SOIC; No. of Pins:16; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| IL3585-3-01 | 制造商:NVE Corporation 功能描述:BOARD EVAL FOR IL3585-3E |
| IL3585-3E | 制造商:NVE Corporation 功能描述:IC TRANSCEIVER RS485 16SOIC |
| IL3585E | 功能描述:TXRX ISO PROFIBUS RS485 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:IsoLoop® 標準包裝:1 系列:- 類型:線路收發器 驅動器/接收器數:5/3 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:Digi-Reel® 產品目錄頁面:918 (CN2011-ZH PDF) 其它名稱:296-25096-6 |
| IL3585ETR13 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PROFIBUS Compatible Isolated RS485 Interface |
發布緊急采購，3分鐘左右您將得到回復。