- 您現在的位置：買賣IC網 > PDF目錄360861 > INA103KU Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | INA103KU |
| 元件分類： | 測量放大器 |
| 英文描述： | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| 中文描述： | 單電源，軌至軌，低成本儀表放大器 |
| 文件頁數： | 10/12頁 |
| 文件大小： | 297K |
| 代理商： | INA103KU |
INA103
10
Figure 6 shows an active control loop that adjusts the output
offset voltage to zero. A
, R, and C form an integrator that
produces an offsetting voltage applied to one input of the
INA103. This produces a –6dB/octave low frequency roll-
off like the capacitor input coupling in Figure 5.
COMMON-MODE INPUT RANGE
For proper operation, the combined differential input signal
and common-mode input voltage must not cause the input
amplifiers to exceed their output swing limits. The linear
input range is shown in the typical performance curve
“Maximum Common-Mode Voltage vs Output Voltage.”
For a given total gain, the input common-mode range can be
increased by reducing the input stage gain and increasing the
output stage gain with the circuit shown in Figure 7.
OUTPUT SENSE
An output sense terminal allows greater gain accuracy in
driving the load. By connecting the sense connection at the
load, IR voltage loss to the load is included inside the
feedback loop. Current drive can be increased by connect-
ing a current booster inside the feedback loop as shown in
Figure 11.
FIGURE 6. Automatic DC Restoration.
FIGURE 4. Output Offsetting.
FIGURE 5. Input Offset Adjustment for AC-Coupled Inputs.
11
10
7
16
15
13
14
6
2
1
INA103
–In
+In
50k
(1)
50k
(1)
100k
(1)
V
OUT
Gain = 100V/V
(40dB)
NOTE: (1) 50k R, 100k pot is
max recommended value. Use
smaller values in this ratio if possible.
I
B–
I
B+
I
B–
≈
I
B+
≈
2.5μA
11
10
7
16
15
13
14
6
2
1
INA103
–In
+In
100k
(1)
V
OUT
+
–
100k
(1)
10k
2k
100k
R
C
1μF
Gain = 100V/V
(40dB)
NOTE: (1) 100k is max recommended
value. Use smaller value if possible.
1/2 OPA1013
A
2
f
–3dB
=
Gain
12
π
RC
1110
7
16
15
13
14
6
2
1
INA103
150
–
+
150
10k
OPA27
100μA
(1)
Offset Adjustment
Range = ±15mV
V–
V
OUT
V+
NOTE: (1)
1/2 REF200
100μA
(1)
V
IN
Gain = 1V/V
(0dB)
相關PDF資料 |
PDF描述 |
|---|---|
| INA103 | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA103KP | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA104 | Very-High Accuracy INSTRUMENTATION AMPLIFIER |
| INA104AM | RES THKF 0805 .125W 5% 680 OHM ROHS |
| INA104BM | Very-High Accuracy INSTRUMENTATION AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA103KU | 制造商:Texas Instruments 功能描述:IC SM AMP INSTRUMENTATION |
| INA103KU | 制造商:Texas Instruments 功能描述:AMP INSTRUMENTATION SOIC16 103 |
| INA103KU/1K | 功能描述:儀表放大器 Low-Noise Low-Distortion RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA103KU/1KE4 | 功能描述:儀表放大器 Low-Noise Low-Distortion RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA103KUG4 | 功能描述:儀表放大器 Lo Noise Lo Distort Instrum Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。