- 您現在的位置：買賣IC網 > PDF目錄360861 > INA106KU Precision Gain = 10 DIFFERENTIAL AMPLIFIER PDF資料下載
參數資料
| 型號： | INA106KU |
| 元件分類： | 差分放大器 |
| 英文描述： | Precision Gain = 10 DIFFERENTIAL AMPLIFIER |
| 中文描述： | 精密增益\u003d 10 DIFFERENTI鋁放大器 |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 175K |
| 代理商： | INA106KU |
INA106
5
TYPICAL PERFORMANCE CURVES
(CONT)
At T
A
= +25
°
C, V
S
=
±
15V, unless otherwise noted.
POWER SUPPLY REJECTION
vs FREQUENCY
Frequency (Hz)
P
140
120
100
80
60
40
1
10
100
1k
10k
100k
V–
V+
CMR vs FREQUENCY
Frequency (Hz)
C
110
100
90
80
70
60
10
100
1k
10k
100k
APPLICATIONS INFORMATION
Figure 1 shows the basic connections required for operation
of the INA106. Power supply bypass capacitors should be
connected close to the device pins as shown.
FIGURE 1. Basic Power Supply and Signal Connections.
The differential input signal is connected to pins 2 and 3 as
shown. The source impedance connected to the inputs must
be equal to assure good common-mode rejection. A 5
mismatch in source impedance will degrade the common-
mode rejection of a typical device to approximately 86dB. If
the source has a known source impedance mismatch, an
additional resistor in series with one input can be used to
preserve good common-mode rejection.
The output is referred to the output reference terminal
(pin 1) which is normally grounded. A voltage applied to the
Ref terminal will be summed with the output signal. The
source impedance of a signal applied to the Ref terminal
should be less than 10
to maintain good common-mode
rejection.
Figure 2 shows a voltage applied to pin 1 to trim the offset
voltage of the INA106. The known 100
source impedance
of the trim circuit is compensated by the 10
resistor in
series with pin 3 to maintain good CMR.
V
2
2
5
6
INA106
V
OUT
= 10(V
3
–V
2
)
1
R
4
100k
V
3
R
1
10k
R
3
10k
3
R
2
100k
1μF
V–
1μF
V+
4
7
+
–
FIGURE 2. Offset Adjustment.
V
2
2
5
6
INA106
V
O
1
R
4
R
1
R
3
3
R
2
499k
100
100k
+15V
–15V
V
3
10
V
= V
– V
Offset Adjustment Range = ±3mV
Compensates for
some impedance
at pin 1. See text.
Referring to Figure 1, the CMR depends upon the match of
the internal R
4
/R
3
ratio to the R
1
/R
2
ratio. A CMR of 106dB
requires resistor matching of 0.005%. To maintain high
CMR over temperature, the resistor TCR tracking must be
better than 2ppm/
°
C. These accuracies are difficult and
expensive to reliably achieve with discrete components.
相關PDF資料 |
PDF描述 |
|---|---|
| INA106 | Precision Gain = 10 DIFFERENTIAL AMPLIFIER |
| INA106KP | Precision Gain = 10 DIFFERENTIAL AMPLIFIER |
| INA110AG-BI | Instrumentation Amp， Fixed Gain |
| INA110BG-BI | Instrumentation Amp， Fixed Gain |
| INA110KU-BI | Instrumentation Amp， Fixed Gain |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA106U | 功能描述:差分放大器 Precision Fixed-Gain RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
| INA106U | 制造商:Texas Instruments 功能描述:IC AMP DIFF FIXED GAIN SOIC8 106 |
| INA106U/2K5 | 功能描述:差分放大器 Prec Fixed-Gain Diff Amp RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
| INA106U/2K5G4 | 功能描述:差分放大器 Prec Fixed-Gain Diff Amp RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
| INA106U-2K5 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Precision Gain = 10 DIFFERENTIAL AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。