- 您現在的位置：買賣IC網 > PDF目錄360864 > INA163 Precision Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | INA163 |
| 元件分類： | 測量放大器 |
| 英文描述： | Precision Instrumentation Amplifier |
| 中文描述： | 精密儀表放大器 |
| 文件頁數： | 7/11頁 |
| 文件大小： | 250K |
| 代理商： | INA163 |
INA163
SBOS177B
7
www.ti.com
FIGURE 3. Offset Voltage Adjustment Circuit.
FIGURE 2. Input Stabilization Network.
V+
V
-
V
O
8
4
3
12
5
11
6
10
9
V
IN
V
IN+
INA163
47
47
1.2
m
H
1.2
m
H
INPUT CONSIDERATIONS
Very low source impedance (less than 10
) can cause
the INA163 to oscillate. This depends on circuit layout,
signal source, and input cable characteristics. An input
network consisting of a small inductor and resistor, as
shown in Figure 2, can greatly reduce any tendency to
oscillate. This is especially useful if a variety of input
sources are to be connected to the INA163. Although
not shown in other figures, this network can be used as
needed with all applications shown.
INA163
V+
V
-
V
O
V+
150
10k
150
100
m
A
100
m
A
8
4
3
12
R
G
5
10
11
6
9
V
-
OPA237
+15V
-
15V
V
O
±
250mA
Output Drive
BW
BUF634
connected
for wide bandwidth.
8
11
6
4
5
10
9
INA163
BUF634
Sense
FIGURE 4. Buffer for Increase Output Current.
OFFSET VOLTAGE TRIM
A variable voltage applied to pin 10, as shown in
Figure 3, can be used to adjust the output offset voltage.
A voltage applied to pin 10 is summed with the output
signal. An op amp connected as a buffer is used to
provide a low impedance at pin 10 to assure good
common-mode rejection.
OUTPUT SENSE
An output sense terminal allows greater gain accuracy
in driving the load. By connecting the sense connection
at the load, I R voltage loss to the load is included
inside the feedback loop. Current drive can be in-
creased by connecting a buffer amp inside the feed-
back loop, as shown in Figure 4.
相關PDF資料 |
PDF描述 |
|---|---|
| INA163UA | Precision Instrumentation Amplifier |
| INA168 | High-Side Measurement CURRENT SHUNT MONITOR |
| INA138 | High-Side Measurement CURRENT SHUNT MONITOR |
| INA170 | High-Side, Bidirectional CURRENT SHUNT MONITOR |
| INA170EA250 | High-Side, Bidirectional CURRENT SHUNT MONITOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA163_06 | 制造商:BB 制造商全稱:BB 功能描述:Low-Noise, Low-Distortion INSTRUMENTATION AMPLIFIER |
| INA163UA | 功能描述:儀表放大器 Low-Noise Low-Distortion RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA163UA/2K5 | 功能描述:儀表放大器 Low-Noise Low-Distortion RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA163UA/2K5E4 | 功能描述:儀表放大器 Low-Noise Low-Distortion RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA163UAE4 | 功能描述:儀表放大器 Low-Noise Low-Distortion RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。