- 您現在的位置：買賣IC網 > PDF目錄377498 > IR2166 (International Rectifier) RES 560 OHM 1/10W 5% SM PDF資料下載
參數資料
| 型號： | IR2166 |
| 廠商： | International Rectifier |
| 英文描述： | RES 560 OHM 1/10W 5% SM |
| 中文描述： | 功率因數校正 |
| 文件頁數： | 21/29頁 |
| 文件大?。?/td> | 371K |
| 代理商： | IR2166 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
IR2166
www.irf.com
21
Ignition Mode (IGN)
The ignition mode is defined as the state the IC
is in when a high voltage is being established
across the lamp necessary for igniting the lamp.
The IR2166 enters ignition mode when the
voltage on pin CPH exceeds 10V.
Pin CPH is connected internally to the gate of a
P-channel MOSFET (S4) (see Figure 4) that
connects pin RPH with pin RT. As pin CPH
exceeds 10V, the gate-to-source voltage of
MOSFET S4 begins to fall below the turn-on
threshold of S4. As pin CPH continues to ramp
towards VCC, switch S4 turns off slowly. This
results in resistor RPH being disconnected
smoothly from resistor RT, which causes the
operating frequency to ramp smoothly from the
preheat frequency, through the ignition frequency,
to the final run frequency. The over-current
threshold on pin CS will protect the ballast
against a non-strike or open-filament lamp fault
condition. The voltage on pin CS is defined by
the lower half-bridge MOSFET current flowing
through the external current sensing resistor
RCS. The resistor RCS therefore programs the
maximum allowable peak ignition current (and
therefore peak ignition voltage) of the ballast
output stage. If the number of over current pulses
exceed 25, the IC will enter fault mode and gate
driver outputs HO, LO and PFC will be latched
low.
Run Mode (RUN)
Once the lamp has successfully ignited, the
ballast enters run mode. The run mode is defined
as the state the IC is in when the lamp arc is
established and the lamp is being driven to a
given power level. The run mode oscillating
frequency is determined by the timing resistor
RT and timing capacitor CT (see Design
Equations, page 26, Equations 3 and 4). Should
hard-switching occur at the half-bridge at any
time due to an open-filament or lamp removal,
the voltage across the current sensing resistor,
RCS, will exceed the internal threshold of 1.3 volts
and the IC will enter FAULT mode and gate driver
outputs HO, LO and PFC will be latched low.
DC Bus Under-voltage Reset
Should the DC bus decrease too low during a
brownout line condition or overload condition,
the resonant output stage to the lamp can shift
near or below resonance. This can produce
hard-switching at the half-bridge which can
damage the half-bridge switches or, the DC bus
can decrease too far and the lamp can
extinguish. To protect against this, the VBUS pin
includes a 3.0V under-voltage threshold. Should
the voltage at the VBUS pin decrease below 3.0V,
VCC will be discharged to the UVLO- threshold
and all gate driver outputs will be latched low.
For proper ballast design, the designer should
design the PFC section such that the DC bus
does not drop until the AC line input voltage falls
below the rated input voltage of the ballast (See
PFC section). When correctly designed, the
voltage measured at the VBUS pin will decrease
below the internal 3.0V threshold and the ballast
will turn off cleanly. The pull-up resistor to VCC
(RSUPPLY) will then turn the ballast on again
with the AC input line voltage increasing to the
minimum specified value causing VCC to exceed
UVLO+.
R
SUPPLY
should be set to turn the ballast on at
the minimum specified ballast input voltage. The
PFC should then be designed such that the DC
bus decreases at an input line voltage that is
相關PDF資料 |
PDF描述 |
|---|---|
| IR2166PBF | PFC & BALLAST CONTROL IC |
| IR2166S | PFC & BALLAST CONTROL IC |
| IR2167 | PFC BALLAST CONTROL IC |
| IR2167S | PFC Ballast Control. Thermal Overload Protection. Brown Out Protection. Programmable Preheat and Frequency. Programmable Deadtime in a 20 Lead SOIC package |
| IR2170 | OVER CURRENT SENSING IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IR2166PBF | 功能描述:功率驅動器IC PFC Ballast Cntrl RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| IR2166PBF | 制造商:International Rectifier 功能描述:Controller IC Output Voltage Max.:25V |
| IR2166S | 功能描述:IC PFC/BALLAST CONTROL 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 照明，鎮流器控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:CCFL 控制器 頻率:40 ~ 80 kHz 電流 - 電源:5mA 電流 - 輸出:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) 其它名稱:90-3991V+V01 |
| IR2166SPBF | 功能描述:功率驅動器IC PFC BALLAST CTRL IC 600V 15.6V VCC ESD RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| IR2166STRPBF | 功能描述:功率驅動器IC PFC Ballast Cntrl RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。