- 您現在的位置：買賣IC網 > PDF目錄384487 > IR3092MTR (International Rectifier) 2 PHASE OPTERON, ATHLON, OR VR10.X CONTROL IC PDF資料下載
參數資料
| 型號： | IR3092MTR |
| 廠商： | International Rectifier |
| 英文描述： | 2 PHASE OPTERON, ATHLON, OR VR10.X CONTROL IC |
| 中文描述： | 2相皓龍，速龍，或控制IC的VR10.X |
| 文件頁數： | 33/37頁 |
| 文件大?。?/td> | 619K |
| 代理商： | IR3092MTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁
IR3092
Page 33 of 37
06/25/04
PCB AND STENCIL DESIGN METHODOLOGY
x
7x7
x
48 Lead
x
0.5mm pitch MLPQ
See Figures 14-16.
PCB Metal Design (0.5mm Pitch Leads)
1. Lead land width should be equal to nominal part lead width. The minimum lead to lead spacing
should be
PP WR PLQLPL]H VKRUWLQJ
2. Lead land length should be equal to maximum part lead length + 0.2 mm outboard extension +
0.05mm inboard extension. The outboard extension ensures a large and inspectable toe fillet,
and the inboard extension will accommodate any part misalignment and ensure a fillet.
3. Center pad land length and width should be = maximum part pad length and width. However, the
minimum metal to metal spacing should be
and
PP IRU
R] &RSSHU
4. Sixteen 0.30mm diameter vias shall be placed in the pad land spaced at 1.2mm, and connected
to ground to minimize the noise effect on the IC, and to transfer heat to the PCB.
PCB Solder Resist Design (0.5mm Pitch Leads)
1. Lead lands. The solder resist should be pulled away from the metal lead lands by a minimum of
0.060mm. The solder resist mis-alignment is a maximum of 0.050mm and it is recommended
that the lead lands are all NSMD. Therefore pulling the S/R 0.060mm will always ensure NSMD
pads.
2. The minimum solder resist width is 0.13mm, therefore it is recommended that the solder resist is
completely removed from between the lead lands forming a single opening for each “group” of
lead lands.
3. At the inside corner of the solder resist where the lead land groups meet, it is recommended to
provide a fillet so a solder resist width of
4. Land Pad. The land pad should be SMD, with a minimum overlap of the solder resist onto the
copper of 0.060mm to accommodate solder resist mis-alignment. In 0.5mm pitch cases it is
allowable to have the solder resist opening for the land pad to be smaller than the part pad.
5. Ensure that the solder resist in-between the lead lands and the pad land is
high aspect ratio of the solder resist strip separating the lead lands from the pad land.
6. The single via in the land pad should be tented with solder resist 0.4mm diameter, or 0.1mm
larger than the diameter of the via.
Stencil Design (0.5mm Pitch Leads)
1. The stencil apertures for the lead lands should be approximately 80% of the area of the lead
lands. Reducing the amount of solder deposited will minimize the occurrence of lead shorts.
Since for 0.5mm pitch devices the leads are only 0.25mm wide, the stencil apertures should not
be made narrower; openings in stencils < 0.25mm wide are difficult to maintain repeatable solder
release.
2. The stencil lead land apertures should therefore be shortened in length by 80% and centered on
the lead land.
3. The center land pad aperture should be striped with 0.25mm wide openings and spaces to
deposit approximately 50% area of solder on the center pad. If too much solder is deposited on
the center land pad the part will float and the lead lands will be open.
4. The maximum length and width of the center land pad stencil aperture should be equal to the
solder resist opening minus an annular 0.2mm pull back to decrease the incidence of shorting
the center land to the lead lands when the part is pushed into the solder paste.
PP
R] &RSSHU
PP IRU
R] &RSSHU
PP UHPDLQV
PP GXH WR WKH
相關PDF資料 |
PDF描述 |
|---|---|
| IR3220 | FULLY PROTECTED H-BRIDGE FOR D.C. MOTOR |
| IR3500 | XPHASE3TM VR11.0 & AMD PVID CONTROL IC |
| IR3500MPBF | XPHASE3TM VR11.0 & AMD PVID CONTROL IC |
| IR3500MTRPBF | XPHASE3TM VR11.0 & AMD PVID CONTROL IC |
| IR3623MPBF | HIGH FREQUENCY 2-PHASE, SINGLE OR DUAL OUTPUT SYNCHRONOUS STEP DOWN CONTROLLER WITH OUTPUT TRACKING AND SEQUENCING |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IR3092MTRPBF | 功能描述:IC CONTROLLER 2PHASE 48-MLPQ RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| IR3093M | 制造商:IRF 制造商全稱:International Rectifier 功能描述:3 PHASE OPTERON, ATHLON, OR VR10.X CONTROL IC |
| IR3093MPBF | 功能描述:IC VID VOLTAGE PROGRAMMER 48MLPQ RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| IR3093MTR | 制造商:IRF 制造商全稱:International Rectifier 功能描述:3 PHASE OPTERON, ATHLON, OR VR10.X CONTROL IC |
| IR3093MTRPBF | 功能描述:IC CTLR 3PHASE VR10 48-MLQP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。