- 您現在的位置：買賣IC網 > PDF目錄377537 > IRMDAC3 (International Rectifier) Reference Design Kit: 3-Phase 460VAC 3HP Motor Drive PDF資料下載
參數資料
| 型號： | IRMDAC3 |
| 廠商： | International Rectifier |
| 英文描述： | Reference Design Kit: 3-Phase 460VAC 3HP Motor Drive |
| 中文描述： | 參考設計工具包：三相460VAC功率3HP電機驅動 |
| 文件頁數： | 4/9頁 |
| 文件大?。?/td> | 105K |
| 代理商： | IRMDAC3 |
Power Module Mounting and Hook-up Instructions
1.
2.
3.
4.
Remove all particles and grit from the heatsink and power substrate
Spread a thin layer of silicone grease on the heatsink, covering the entire area that the power substrate will occupy
Place the power substrate onto the heatsink with the mounting holes aligned and press firmly into the grease
Place the 2XM4 mounting screws and tighten to 1NM torque
External Connections
All input and output control connections are made via a 16-terminal single in line connector J6. Three phase input connections
are made to terminals R,S and T of J1. Inverter output terminal connections are made to terminals U,V and W of J7. Positive
DC Bus and brake IGBT collector connections are available on terminals P and BR respectively of J5. An external power
resistor may be connected between P and BR to dissipate braking energy.
Power-Up Procedure
Upon application of 3-phase input power, PWM inputs must be held high until the protection latch circuitry is reset. To reset
this latch before inverter start-up, RESET pin on J6 connector must be pulled down low for at least 2usec. This will set the
Fault feedback signal on J6 high. PWM input signals may then be actively driven.
2
1
IRMDAC3
Reference Design Data Sheet (October 1998)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
J6
VDD +5V
VCC +15V
N [DC bus (-) ]
IN1
IN2
IN3
IN4
IN5
IN6
FAULT
IFB
VFB
RESET
NC
IN7
STOP
1
2
3
J1
1
2
3
J7
R
S
T
U
V
W
1
2
J5
BR
P
Figure 4 Signal Connector
Figure 6 Power Module Mounting Screw Sequence
Figure 5 Power Terminal Blocks
相關PDF資料 |
PDF描述 |
|---|---|
| IRMDSS1 | IR1110 Soft Start IC Reference Design Kit For AC Motor Drives, UPS, Welders, and other applications |
| IRPLDIM1 | PLAQUE |
| IRPLDIM1U | Dimming Ballast Control IC Design Kit |
| IRPLDIM2U | Digital Dimming DALI Ballast for 32W/T8 110V input |
| IRPT1053C | Power Module for 1 hp Motor Drives |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IRMDSS1 | 功能描述:KIT DESIGN IC REF SOFT START RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| IRMFB-EK | 功能描述:光學傳感器開發工具 Si1140 Multifunction Demo Board RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
| IRM-H136/TR2 | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:Infrared Remote-control Receiver Module |
| IRM-H136-TR2 | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:Infrared Remote-control Receiver Module |
| IRM-H138/TR2 | 功能描述:紅外接收機 Infrared Remote RoHS:否 制造商:Vishay Semiconductors 載頻:20 kHz to 60 kHz 傳輸距離:5 m 顯示角:+/- 50 deg 高電平脈沖寬度: 低電平脈沖寬度: 最小高電平輸出電壓: 輸出電流:5 mA 工作電壓:2.5 V to 5.5 V 電源電流:0.9 mA 功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。