- 您現在的位置：買賣IC網 > PDF目錄377541 > IRU3021MCW (International Rectifier) 5-BIT PROGRAMMABLE SYNCHRONOUS BUCK PLUS TRIPLE LDO CONTROLLER PDF資料下載
參數資料
| 型號： | IRU3021MCW |
| 廠商： | International Rectifier |
| 英文描述： | 5-BIT PROGRAMMABLE SYNCHRONOUS BUCK PLUS TRIPLE LDO CONTROLLER |
| 中文描述： | 5位可編程同步降壓普樂士三重LDO控制器 |
| 文件頁數： | 5/8頁 |
| 文件大小： | 113K |
| 代理商： | IRU3021MCW |
IRU3021M
5
Rev. 1.4
07/24/01
This pin provides shutdown for all the regulators. A TTL compatible, logic level high applied
to this pin disables all the outputs and discharges the soft-start capacitor. The SD signal
turns off the synchronous MOSFET allowing body diode to conduct and discharge the
output capacitor.
This pin provides the feedback for the AGP linear regulator. The Select pin when con-
nected to the "Type Detect" pin of the AGP slot automatically selects the right voltage for
the AGP V
DDQ
.
This pin provides automatic voltage selection for the AGP switching regulator. When it is
pulled LO, the voltage is 1.5V and when left open or pulled to HI, the voltage is 3.3V.
This pin provides the soft-start for all the regulators. An internal current source charges an
external capacitor that is connected from this pin to ground which ramps up the outputs of
the regulators, preventing the outputs from overshooting as well as limiting the input cur-
rent. The second function of the Soft-Start cap is to provide long off time (HICCUP) for the
synchronous MOSFET during current limiting.
This pin has dual function. It acts as an output of the over-voltage protection circuitry or it
can be used to program the frequency using an external resistor. When used as a fault
detector, if any of the switcher outputs exceed the OVP trip point, the Fault pin switches
to 12V and the soft-start cap is discharged. If the Fault pin is to be connected to any
external circuitry, it needs to be buffered.
This pin provides the feedback for the linear regulator that its output drive is Drive4.
This pin controls the gate of an external MOSFET for the 1.8V chip set linear regulator.
This pin is not connected internally.
This pin serves as the ground pin and must be connected directly to the ground plane.
This pin controls the gate of an external transistor for the 1.5V GTL+ linear regulator.
This pin provides the feedback for the linear regulator that its output drive is Drive3.
5V supply voltage. A high frequency capacitor (0.1 to 1
μ
F) must be placed close to this
pin and connected from this pin to the ground plane for noise free operation.
This pin provides the feedback for the synchronous switching regulator. Typically this pin
can be connected directly to the output of the switching regulator. However, a resistor
divider is recommended to be connected from this pin to Vout1 and ground to adjust the
output voltage for any drop in the output voltage that is caused by the trace resistance.
The value of the resistor connected from Vout1 to Fb1 must be less than 1000
.
This pin is internally connected to the under-voltage and over-voltage comparators sens-
ing the Vcore status. It must be connected directly to the Vcore supply.
This pin is connected to the Drain of the power MOSFET of the Core supply and it provides
the positive sensing for the internal current sensing circuitry. An external resistor pro-
grams the current sense threshold depending on the R
DS
of the power MOSFET. An
external capacitor is placed in parallel with the programming resistor to provide high fre-
quency noise filtering.
This pin serves as the Power ground pin and must be connected directly to the ground
plane close to the source of the synchronous MOSFET. A high frequency capacitor (typi-
cally 1
μ
F) must be connected from V12 pin to this pin for noise free operation.
Output driver for the synchronous power MOSFET for the Core supply.
This pin is connected to the source of the power MOSFET for the Core supply and it
provides the negative sensing for the internal current sensing circuitry.
Output driver for the high side power MOSFET for the Core supply.
This pin is connected to the 12V supply and serves as the power Vcc pin for the output
drivers. A high frequency capacitor (typically 1
μ
F) must be placed close to this pin and
PGnd pin and be connected directly from this pin to the ground plane for the noise free
operation.
PIN# PIN SYMBOL PIN DESCRIPTION
9
SD
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Vsen2
Select
SS
Fault / Rt
Vsen4
Drive4
NC
Gnd
Drive3
Vsen3
V5
Fb
Vsen1
OCSet
PGnd
LGate
Phase
UGate
V12
相關PDF資料 |
PDF描述 |
|---|---|
| IRU3027 | 5-BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC WITH TRIPLE LDO CONTROLLER |
| IRU3027CW | 5-BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC WITH TRIPLE LDO CONTROLLER |
| IRU3034 | 8-PIN PWM SWITCHER CONTROLLER IC WITH CURRENT LIMITING |
| IRU3034CSPBF | 8-PIN PWM SWITCHER CONTROLLER IC WITH CURRENT LIMITING |
| IRU3034PBF | 8-PIN PWM SWITCHER CONTROLLER IC WITH CURRENT LIMITING |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IRU3021MCWTR | 功能描述:IC CTRL/REG SYNC BUCK 28-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| IRU3027 | 制造商:IRF 制造商全稱:International Rectifier 功能描述:5-BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC WITH TRIPLE LDO CONTROLLER |
| IRU3027CW | 功能描述:IC CTRL/REG SYNC BUCK 28-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| IRU3027CWPBF | 制造商:International Rectifier 功能描述:DC DC Cntrlr Quad-OUT Synchronous Buck Controller/PWM DC to DC Controller 28-Pin SOIC W Tube |
| IRU3027CWTR | 功能描述:IC CTRL/REG SYNC BUCK 28-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。