- 您現在的位置：買賣IC網 > PDF目錄377579 > IS93C56A (Integrated Silicon Solution, Inc.) 2K-BIT/4K-BIT SERIAL ELECTRICALLY ERASABLE PROM PDF資料下載
參數資料
| 型號： | IS93C56A |
| 廠商： | Integrated Silicon Solution, Inc. |
| 英文描述： | 2K-BIT/4K-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| 中文描述： | 2K-BIT/4K-BIT串行電可擦除可編程ROM |
| 文件頁數： | 3/16頁 |
| 文件大小： | 136K |
| 代理商： | IS93C56A |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. A
05/02/06
3
IS93C56A IS93C66A
ISSI
Write All (WRALL)
The write all (WRALL) instruction programs all registers
with the data pattern specified in the instruction. As with the
WRITE instruction, the falling edge of CS must occur to
initiate the self-timed programming cycle. If CS is then
brought HIGH after a minimum wait of 200 ns (t
CS
), the D
OUT
pin indicates the READY/
BUSY
status of the chip (see
Figure 6). Vcc is required to be above 4.5V for WRALL to
function properly.
Write Disable (WDS)
The write disable
(WDS)
instruction disables all programming
capabilities. This protects the entire device against acci-
dental modification of data until a WEN instruction is
executed. (When Vcc is applied, this part powers up in the
write disabled state.) To protect data, a WDS instruction
should be executed upon completion of each programming
operation.
Erase Register (ERASE)
After the erase instruction is entered, CS must be brought
LOW. The falling edge of CS initiates the self-timed internal
programming cycle. Bringing CS HIGH after a minimum of
t
CS
, will cause D
OUT
to indicate the
READ/
BUSY
chip: a logical “0” indicates programming is still in progress;
a logical “1” indicates the erase cycle is complete and the
part is ready for another instruction (see Figure 8).
Erase All (ERAL)
Full chip erase is provided for ease of programming. Erasing
the entire chip involves setting all bits in the entire memory
array to a logical “1” (see Figure 9). Vcc is required to be
above 4.5V for ERALL to function properly.
Write Enable (WEN)
The write enable (WEN) instruction must be executed
before any device programming (WRITE, WRALL,
ERASE, and ERAL) can be done. When Vcc is applied,
this device powers up in the write disabled state. The
device then remains in a write disabled state until a WEN
instruction is executed. Thereafter, the device remains
enabled until a WDS instruction is executed or until Vcc
is removed. (See Figure 4.) (Note: Chip select must
remain LOW until Vcc reaches its operational value.)
Write (WRITE)
The WRITE instruction includes 8 or 16 bits of data to be
written into the specified register. After the last data bit
has been applied to D
IN
, and before the next rising edge
of SK, CS must be brought LOW. If the device is write-
enabled, then the falling edge of CS initiates the self-
timed programming cycle (see WEN).
If CS is brought HIGH, after a minimum wait of 200 ns (5V
operation) after the falling edge of CS (t
CS
) D
OUT
will
indicate the READY/
BUSY
status of the chip. Logical “0”
means programming is still in progress; logical “1” means
the selected register has been written, and the part is
ready for another instruction (see Figure 5). The READY/
BUSY
status will not be available if: a) The CS input goes
HIGH after the end of the self-timed programming cycle,
t
WP
; or b) Simultaneously CS is HIGH, Din is HIGH, and
SK goes HIGH, which clears the status flag.
相關PDF資料 |
PDF描述 |
|---|---|
| IS93C56A-2GRI | 2K-BIT/4K-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| IS93C56A-2GRLI | 2K-BIT/4K-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| IS93C56A-2PI | 2K-BIT/4K-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| IS93C56A-2PLI | 2K-BIT/4K-BIT SERIAL ELECTRICALLY ERASABLE PROM |
| IS93C56A-2ZI | 2K-BIT/4K-BIT SERIAL ELECTRICALLY ERASABLE PROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IS93C56A-2GRI | 功能描述:電可擦除可編程只讀存儲器 1.8V 2Kb Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| IS93C56A-2GRI-TR | 功能描述:電可擦除可編程只讀存儲器 1.8V 2Kb Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| IS93C56A-2GRLI | 功能描述:電可擦除可編程只讀存儲器 1.8V 2Kb Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| IS93C56A-2GRLI-TR | 功能描述:電可擦除可編程只讀存儲器 1.8V 2Kb Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| IS93C56A-2PI | 功能描述:電可擦除可編程只讀存儲器 1.8V 2Kb Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。