- 您現在的位置：買賣IC網 > PDF目錄9379 > ISL12024IVZ-T (Intersil)IC RTC/CALENDAR EEPROM 8-TSSOP PDF資料下載
參數資料
| 型號： | ISL12024IVZ-T |
| 廠商： | Intersil |
| 文件頁數： | 7/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC/CALENDAR EEPROM 8-TSSOP |
| 標準包裝： | 2,500 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，唯一 ID |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 8-TSSOP |
| 包裝： | 帶卷 (TR) |
15
FN6370.3
August 18, 2008
Start Condition
All commands are preceded by the start condition, which is a
HIGH to LOW transition of SDA when SCL is HIGH. The
device continuously monitors the SDA and SCL lines for the
start condition and will not respond to any command until
this condition has been met (see Figure 13).
Stop Condition
All communications must be terminated by a stop condition,
which is a LOW to HIGH transition of SDA when SCL is
HIGH. The stop condition is also used to place the device
into the Standby Power Mode after a read sequence. A stop
condition can only be issued after the transmitting device
has released the bus (see Figure 13).
Acknowledge
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device, either
master or slave, will release the bus after transmitting 8 bits.
During the ninth clock cycle, the receiver will pull the SDA
line LOW to acknowledge that it received the 8 bits of data
(see Figure 14).
The device will respond with an acknowledge after
recognition of a start condition and if the correct Device
Identifier and Select bits are contained in the Slave Address
Byte. If a write operation is selected, the device will respond
with an acknowledge after the receipt of each subsequent
8-bit word. The device will not acknowledge if the slave
address byte is incorrect.
In the read mode, the device will transmit 8-bits of data,
release the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no stop
condition is generated by the master, the device will continue
to transmit data. The device will terminate further data
transmissions if an acknowledge is not detected. The master
must then issue a stop condition to return the device to
Standby Power Mode and place the device into a known
state.
SCL
SDA
DATA STABLE
DATA CHANGE
DATA STABLE
FIGURE 12. VALID DATA CHANGES ON THE SDA BUS
SCL
SDA
START
STOP
FIGURE 13. VALID START AND STOP CONDITIONS
SCL FROM
MASTER
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
8
1
9
START
ACKNOWLEDGE
FIGURE 14. ACKNOWLEDGE RESPONSE FROM RECEIVER
ISL12024
相關PDF資料 |
PDF描述 |
|---|---|
| AD5112BCPZ10-500R7 | IC DGTL POT 64POS 10K 8LFCSP |
| AD5112BCPZ80-500R7 | IC DGTL POT 64POS 80K 8LFCSP |
| ISL12026AIVZ | IC RTC/CALENDAR EEPROM 8-TSSOP |
| VI-2NM-MW | CONVERTER MOD DC/DC 10V 100W |
| AD5113BCPZ5-500R7 | IC DGTL POT 64POS 5K 8LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL12025 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Real-Time Clock/Calendar with EEPROM |
| ISL12025IBZ | 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/EEPROM 2 63VSET RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL12025IBZ-T | 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/EEPROM 2 63VSET RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL12025IVZ | 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/EEPROM 2 63SET 8 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL12025IVZ-T | 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/EEPROM 2 63SET 8 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。