參數資料
型號: ISL12028IBAZ
廠商: Intersil
文件頁數: 14/29頁
文件大小: 0K
描述: IC RTC/CALENDAR EEPROM 14-SOIC
產品培訓模塊: Solutions for Industrial Control Applications
標準包裝: 1,000
類型: 時鐘/日歷
特點: 警報器,閏年,監控器,監視計時器
時間格式: HH:MM:SS(12/24 小時)
數據格式: YY-MM-DD-dd
接口: I²C,2 線串口
電源電壓: 2.7 V ~ 5.5 V
電壓 - 電源,電池: 1.8 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 14-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 14-SOICN
包裝: 管件
21
FN8233.9
November 30, 2010
the sixteen bit address is initialized to 0h. In this way, a current
address read immediately after the power on reset can
download the entire contents of memory starting at the first
location. Upon receipt of the Slave Address Byte with the R/W
bit set to one, the ISL12028 issues an acknowledge, then
transmits eight data bits. The master terminates the read
operation by not responding with an acknowledge during the
ninth clock and issuing a stop condition. Refer to Figure 23 for
the address, acknowledge, and data transfer sequence.
It should be noted that the ninth clock cycle of the read
operation is not a “don’t care.” To terminate a read operation,
the master must either issue a stop condition during the
ninth cycle or hold SDA HIGH during the ninth clock cycle
and then issue a stop condition.
RANDOM READ
Random read operations allow the master to access any
location in the ISL12028. Prior to issuing the Slave Address
Byte with the R/W bit set to zero, the master must first
perform a “dummy” write operation.
The master issues the start condition and the slave address
byte, receives an acknowledge, then issues the word
address bytes. After acknowledging receipt of each word
address byte, the master immediately issues another start
condition and the slave address byte with the R/W bit set to
one. This is followed by an acknowledge from the device and
then by the 8-bit data word. The master terminates the read
operation by not responding with an acknowledge and then
issuing a stop condition. Refer to Figure 25 for the address,
acknowledge, and data transfer sequence.
In a similar operation called “Set Current Address,” the
device sets the address if a stop is issued instead of the
second start shown in Figure 25. The ISL12028 then goes
into standby mode after the stop and all bus activity will be
ignored until a start is detected. This operation loads the new
address into the address counter. The next Current Address
Read operation will read from the newly loaded address.
This operation could be useful if the master knows the next
address it needs to read, but is not ready for the data.
SEQUENTIAL READ
Sequential reads can be initiated as either a current address
read or random address read. The first data byte is
transmitted as with the other modes; however, the master
now responds with an acknowledge, indicating it requires
additional data. The device continues to output data for each
acknowledge received. The master terminates the read
operation by not responding with an acknowledge and then
issuing a stop condition.
The data output is sequential, with the data from address n
followed by the data from address n + 1. The address
counter for read operations increments through all page and
column addresses, allowing the entire memory contents to
be serially read during one operation. At the end of the
address space, the counter “rolls over” to the start of the
address space and the ISL12028 continues to output data
for each acknowledge received. Refer to Figure 26 for the
acknowledge and data transfer sequence.
S
T
A
R
T
S
T
O
P
SLAVE
ADDRESS
DATA
A
C
K
SDA BUS
SIGNALS FROM
THE SLAVE
SIGNALS FROM
THE MASTER
1
FIGURE 23. CURRENT ADDRESS READ SEQUENCE
FIGURE 24. ACKNOWLEDGE POLLING SEQUENCE
ACK
RETURNED?
ISSUE MEMORY ARRAY SLAVE
ADDRESS BYTE
AFH (READ) OR AEH (WRITE)
BYTE LOAD
COMPLETED BY
ISSUING STOP.
ENTER ACK POLLING
ISSUE STOP
ISSUE START
NO
YES
ISSUE STOP
NO
CONTINUE
NORMAL READ OR
WRITE COMMAND
SEQUENCE
PROCEED
YES
NON-VOLATILE WRITE
CYCLE COMPLETE. CONTINUE
COMMAND SEQUENCE?
ISL12028, ISL12028A
相關PDF資料
PDF描述
VI-J1V-MZ CONVERTER MOD DC/DC 5.8V 25W
VI-J1J-MZ CONVERTER MOD DC/DC 36V 25W
ISL12028IB27AZ IC RTC/CALENDAR EEPROM 14-SOIC
MS27499E20B35SC CONN RCPT 79POS BOX MNT W/SCKT
VI-J1H-MZ CONVERTER MOD DC/DC 52V 25W
相關代理商/技術參數
參數描述
ISL12028IBAZ-T 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM 4 64VSET 14 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12028IBZ 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM IN 14LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12028IBZ-T 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM IN 14LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12028IV27AZ 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM 2 92VSET 14 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12028IV27AZ-T 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM 2 92VSET 14 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube