參數資料
型號： ISL12028IVAZ-T
廠商： Intersil
文件頁數： 8/29頁
文件大?。?/td> 0K
描述： IC RTC/CALENDAR EEPROM 14-TSSOP
產品培訓模塊： Solutions for Industrial Control Applications
標準包裝： 2,500
類型： 時鐘/日歷
特點： 警報器，閏年，監控器，監視計時器
時間格式： HH:MM:SS（12/24 小時）
數據格式： YY-MM-DD-dd
接口： I²C，2 線串口
電源電壓： 2.7 V ~ 5.5 V
電壓 - 電源，電池： 1.8 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 14-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 14-TSSOP
包裝： 帶卷 (TR)
16
FN8233.9
November 30, 2010
for up to a month. See “Application Section” on page 22 for
more information.
There are two options for setting the change-over conditions
from VDD to Battery back-up mode. The BSW bit in the PWR
register controls this operation.
Option 1 - Standard Mode (Default for ISL12028A)
Option 2 - Legacy Mode (Default for ISL12028)
Note that applications that have VBAT > VDD will require the
ISL12028A (standard mode) for proper start-up. Note that
the I2C may or may not be operational during battery
backup, that function is controlled by the SBIB bit. That
operation is covered after the power control section.
OPTION 1 - STANDARD POWER CONTROL MODE
(DEFAULT FOR ISL12028A)
In the Standard mode, the supply will switch over to the
battery when VDD drops below VTRIP or VBAT, whichever is
lower. In this mode, accidental operation from the battery is
prevented since the battery backup input will only be used
when the VDD supply is shut off.
To select Option 1, BSW bit in the Power Register must be
set to “BSW = 0”. Following is a description of power
switchover.
Standard Mode Power Switchover
Normal Operating Mode (VDD) to Battery Backup Mode
(VBAT)
To transition from the VDD to VBAT mode, both of the
following conditions must be met:
- Condition 1:
VDD < VBAT - VBATHYS
where VBATHYS ≈ 50mV
- Condition 2:
VDD < VTRIP
where VTRIP ≈ 2.2V
Battery Backup Mode (VBAT) to Normal Mode (VDD)
The ISL12028 device will switch from the VBAT to VDD mode
when one of the following conditions occurs:
- Condition 1:
VDD > VBAT + VBATHYS
where VBATHYS ≈ 50mV
- Condition 2:
VDD > VTRIP + VTRIPHYS
where VTRIPHYS ≈ 30mV
There are two discrete situations that are possible when
using Standard Mode: VBAT < VTRIP and VBAT > VTRIP.
These two power control situations are illustrated in
Figures 13 and 14.
OPTION 2 - LEGACY POWER CONTROL MODE
(DEFAULT FOR ISL12028)
The Legacy Mode follows conditions set in X1226 products.
In this mode, switching from VDD to VBAT is simply done by
comparing the voltages and the device operates from
whichever is the higher voltage. Care should be taken when
changing from Normal to Legacy Mode. If the VBAT voltage is
higher than VDD, then the device will enter battery backup and
unless the battery is disconnected or the voltage decreases,
the device will no longer operate from VDD. If that is the
situation on initial power-up, then I2C communication may not
be possible. For these applications, the ISL12028A should be
used.
To select Option 2, BSW bit in the Power Register must be
set to “BSW = 1”
Normal Mode (VDD) to Battery Backup Mode (VBAT)
To transition from the VDD to VBAT mode, the following
conditions must be met:
VDD < VBAT - VBATHYS
Battery Backup Mode (VBAT) to Normal Mode (VDD)
The device will switch from the VBAT to VDD mode when the
following condition occurs:
TABLE 7. VBAT TRIP POINT WITH DIFFERENT BSW SETTING
BSW BIT
VBAT TRIP POINT
(V)
POWER CONTROL SETTING
0
2.2
Standard Mode (ISL12028A)
1VDD < VBAT
Legacy Mode (ISL12028)
BATTERY
MODE
VDD
2.2V
FIGURE 13. BATTERY SWITCHOVER WHEN VBAT < VTRIP
VBAT
VTRIP
1.8V
VBAT + VBATHYS
VBAT - VBATHYS
BACKUP
FIGURE 14. BATTERY SWITCHOVER WHEN VBAT > VTRIP
VTRIP
VBAT
VTRIP + VTRIPHYS
BATTERY BACKUP
MODE
VDD
VTRIP
3.0V
2.2V
ISL12028, ISL12028A
相關PDF資料
PDF描述
ISL12028IVZ-T IC RTC/CALENDAR EEPROM 14-TSSOP
ISL12025IVZ-T IC RTC/CALENDAR EEPROM 8-TSSOP
ISL12023IVZ-T IC RTC/CLDR TEMP SNSR 14-TSSOP
ISL12025IBZ-T IC RTC/CALENDAR EEPROM 8-SOIC
ISL12029IVAZ-T IC RTC/CALENDAR EEPROM 14-TSSOP
相關代理商/技術參數
參數描述
ISL12028IVZ 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM IN 14LD RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12028IVZ-T 功能描述:實時時鐘 REAL TIME CLKRTC W/ EPROM IN 14LD T RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12029 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Real Time Clock/Calendar with I2C Bus? and EEPROM
ISL12029_10 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Real Time Clock/Calendar with I2C Busa?￠ and EEPROM
ISL12029_1012 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Real Time Clock/Calendar with I2C Bus? and EEPROM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*