參數資料
型號： ISL12032IVZ-T
廠商： Intersil
文件頁數： 8/26頁
文件大?。?/td> 0K
描述： IC RTC LP BATT BACK SRAM 14TSSOP
產品培訓模塊： Solutions for Industrial Control Applications
標準包裝： 1
類型： 時間事件記錄器
特點： 警報器，SRAM，涓流充電器
存儲容量： 128B
時間格式： HH:MM:SS:hh（12/24 小時）
數據格式： YY-MM-DD-dd
接口： I²C，2 線串口
電源電壓： 2.7 V ~ 5.5 V
電壓 - 電源，電池： 1.8 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 14-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 14-TSSOP
包裝： 標準包裝
產品目錄頁面： 1246 (CN2011-ZH PDF)
其它名稱： ISL12032IVZ-TDKR
16
FN6618.3
May 5, 2011
Event Detection Register (EVIC)
EVENT OUTPUT IN BATTERY MODE ENABLE BIT
(EVBATB)
This bit enables/disables the EVDET pin during battery
backup mode (i.e. VBAT pin supply ON). When the EVBATB
is set to “1”, the Event Detect Output is disabled in battery
backup mode. When the EVBATB is cleared to “0”, the Event
Detect output is enabled in battery backup mode. This
feature can be used to save power during battery mode.
EVENT OUTPUT PULSE MODE (EVIM)
This bit controls the EVDET pin output mode. With EVIM = 0,
the output is in normal mode and when an event is triggered,
the output will be set LOW until reset. With EVIM = 1, the
output is in pulse mode and when an event is triggered, the
device will generate a 200ms to 300ms pulse at the EVDET
output.
EVENT DETECT ENABLE (EVEN)
This bit enables/disables the Event Detect function of the
ISL12032. When this bit is set to “1”, the Event Detect is
active. When this bit is cleared to “0”, the Event Detect is
disabled.
EVENT TIME-BASED HYSTERESIS (EHYS1, EHYS0)
These bits set the amount of time-based hysteresis that is
present at the EVIN pin for deglitching the input signal. The
settings vary from 0ms (hysteresis OFF) to 31.25ms (delay
of 31.25ms to check for change of state at the EVIN pin).
The Hysteresis function and the Event Input Sampling
function work independently.
EVENT INPUT SAMPLING RATE (ESMP)
These bits set the frequency of sampling of the Event Input
(EVIN). The settings include from 1/4Hz (one sample per 4s)
to 2Hz (twice a second), 1Hz, or continuous sampling
(Always ON). The less frequent the sampling, the lower the
current drain, which can affect battery current drain and
battery life.
.
Event Index Register (EVIX)
The Event Index Register provides the index for locating an
individual event that has been stored. The Event recording
function allows recalling up to 4 events, although the Event
counting register will count up to 255 events. The 0th
location corresponds to the first event, and the 1st through
3rd locations correspond to the most recent events, with the
3rd location (11b) representing the latest event. Therefore,
setting EVIX to 03h location and reading the TSEVT section
will access the timestamp information for the most recent
(latest) event. Setting this register to another value will allow
reading the corresponding event from the TSEVT section.
EVENT BIT (EVIX <1:0>)
These bits are the Event Counter Register index bits. EVIX1
is the MSB and EVIX0 is the LSB.
Trickle Charge Register (TRICK)
The trickle charge function allows charging current to flow
from the VDD supply to the VBAT pin through a selectable
current limiting resistor. Disabling the trickle charge function
removes this connection and isolates the battery from the
VDD supply in the case charging is not necessary or harmful
(as in the case with a lithium coin cell battery). Note that
there is no charging diode in series with the trickle charge
resistor, but a switch network that adds a small series
resistance to the charging resistance.
TRICKLE CHARGE BIT (TRKEN)
This bit enables/disables the trickle charge capability for the
backup battery supply. Setting this bit to “1” will enable the
trickle charge. Resetting this bit to “0” will disable the trickle
charge function and isolate the battery from the VDD supply.
TRICKLE CHARGE RESISTOR (TRKRO<1:0>)
These bits allow the user to change the trickle charge
resistor settings according to the maximum current desired
for the battery or super capacitor charging.
TABLE 9. EVENT DETECTION REGISTER (EVIC)
ADDR
7
6
5
4
3
2
1
0
0Eh
X
EVBATB
EVIM
EVEN
EHYS1 EHYS0 ESMP1 ESMP0
TABLE 10. EVENT TIME-BASED HYSTERESIS
EHSYS1
EHSYS0
TIME (ms)
00
0
01
3.9
1
0
16.625
1
31.25
TABLE 11. EVENT INPUT SAMPLING RATE
ESMP1
ESMP2
SAMPLING RATE
00
Always ON
01
2 Hz
10
1 Hz
1
1/4 Hz
TABLE 12. EVENT INDEX REGISTER (EVIX)
ADDR
7
6
5
4
3
2
1
0
0Fh
X
EVIX1
EVIX0
TABLE 13. TRICKLE CHARGE REGISTER (TRICK)
ADDR
7
6
5
4
3
2
1
0
10h
X
TRKEN TRKRO1 TRKRO0
ISL12032
相關PDF資料
PDF描述
VE-J1N-MZ CONVERTER MOD DC/DC 18.5V 25W
VI-J1N-MZ CONVERTER MOD DC/DC 18.5V 25W
VE-J1P-MZ CONVERTER MOD DC/DC 13.8V 25W
ISL1209IU10Z-TK IC RTC LP SRAM EEPROM 10-MSOP
VI-J3Z-EY-F4 CONVERTER MOD DC/DC 2V 20W
相關代理商/技術參數
參數描述
ISL12057 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Cost and Low Power I2C RTC Real Time Clock/Calendar
ISL12057IBZ 功能描述:實時時鐘 REAL TIME CLK W/ ALARM DS1337 COMP RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12057IBZ-T 功能描述:實時時鐘 REAL TIME CLK W/ ALARM DS1337 COMP RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12057IRUZ-T 功能描述:實時時鐘 REAL TIME CLK W/ ALARM DS1337 COMP RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12057IUZ 功能描述:實時時鐘 REAL TIME CLK W/ ALARM DS1337 COMP RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*