參數資料
型號: ISL12058IUZ-T
廠商: Intersil
文件頁數: 5/19頁
文件大小: 0K
描述: IC RTC/CALENDAR I2C-BUS 8-MSOP
標準包裝: 2,500
類型: 時鐘/日歷
特點: 警報器,閏年
時間格式: HH:MM:SS(12/24 小時)
數據格式: YY-MM-DD-dd
接口: I²C,2 線串口
電源電壓: 1.8 V ~ 3.6 V
電壓 - 電源,電池: 1.4 V ~ 1.8 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-MSOP
包裝: 帶卷 (TR)
13
FN6756.0
June 15, 2009
Protocol Conventions
Data states on the SDA line can change only during SCL LOW
periods. SDA state changes during SCL HIGH are reserved for
indicating START and STOP conditions (see Figure 7). On
power-up of the ISL12058, the SDA pin is in the input mode.
All I2C interface operations must begin with a START condition,
which is a HIGH to LOW transition of SDA while SCL is HIGH.
The ISL12058 continuously monitors the SDA and SCL lines
for the START condition and does not respond to any
command until this condition is met (see Figure 7). A START
condition is ignored during the power-up sequence.
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while SCL
is HIGH (see Figure 7). A STOP condition at the end of a read
operation or at the end of a write operation to memory only
places the device in its standby mode.
An acknowledge (ACK) is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after transmitting
8 bits. During the ninth clock cycle, the receiver pulls the SDA
line LOW to acknowledge the reception of the 8 bits of data
(see Figure 8).
The ISL12058 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL12058 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation.
FIGURE 7. VALID DATA CHANGES, START, AND STOP CONDITIONS
FIGURE 8. ACKNOWLEDGE RESPONSE FROM RECEIVER
SDA
SCL
START
DATA
STOP
STABLE
CHANGE
DATA
STABLE
SDA OUTPUT FROM
TRANSMITTER
SDA OUTPUT FROM
RECEIVER
8
1
9
START
ACK
SCL FROM
MASTER
HIGH IMPEDANCE
ISL12058
相關PDF資料
PDF描述
AD5201BRMZ50 IC DGTL POT 50K 33POS 10-MSOP
MS27472P16B6P CONN RCPT 6POS WALL MT W/PINS
VI-J0V-MZ CONVERTER MOD DC/DC 5.8V 25W
MS27484T14F97PB CONN PLUG 12POS STRAIGHT W/PINS
VI-J1Z-MZ CONVERTER MOD DC/DC 2V 10W
相關代理商/技術參數
參數描述
ISL12059 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Cost and Low Power I2C Bus? Real Time Clock/Calendar
ISL12059IBZ 功能描述:實時時鐘 REAL TIME CLK W/ ALARM & TIMR FUNCTNS RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12059IBZ-T 功能描述:實時時鐘 REAL TIME CLK W/ ALARM & TIMR FUNCTNS RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL1208 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM
ISL1208_06 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM