- 您現在的位置：買賣IC網 > PDF目錄9381 > ISL1218IBZ-T (Intersil)IC RTC LP BATT BACKED SRAM 8SOIC PDF資料下載
參數資料
| 型號： | ISL1218IBZ-T |
| 廠商： | Intersil |
| 文件頁數： | 5/21頁 |
| 文件大小： | 0K |
| 描述： | IC RTC LP BATT BACKED SRAM 8SOIC |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 2,500 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，SRAM |
| 存儲容量： | 8B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
13
FN6313.0
June 22, 2006
The effective on-chip series load capacitance, CLOAD,
ranges from 4.5pF to 20.25pF with a mid-scale value of
12.5pF (default). CLOAD is changed via two digitally
controlled capacitors, CX1 and CX2, connected from the X1
CX2 is given by the following formula:
The effective series load capacitance is the combination of
CX1 and CX2:
For example, CLOAD(ATR = 00000) = 12.5pF,
CLOAD(ATR = 100000) = 4.5pF, and CLOAD(ATR=011111)
= 20.25pF. The entire range for the series combination of
load capacitance goes from 4.5pF to 20.25pF in 0.25pF
steps. Note that these are typical values.
BATTERY MODE ATR SELECTION (BMATR <1:0>)
Since the accuracy of the crystal oscillator is dependent on
the VDD/VBAT operation, the ISL1218 provides the capability
to adjust the capacitance between VDD and VBAT when the
device switches between power sources.
DIGITAL TRIMMING REGISTER (DTR <2:0>)
The digital trimming bits DTR0, DTR1, and DTR2 adjust the
average number of counts per second and average the ppm
error to achieve better accuracy.
DTR2 is a sign bit. DTR2 = “0” means frequency
compensation is >0. DTR2 = “1” means frequency
compensation is <0.
DTR1 and DTR0 are both scale bits. DTR1 gives 40ppm
adjustment and DTR0 gives 20ppm adjustment.
A range from -60ppm to +60ppm can be represented by
using these three bits (see Table 5).
Alarm Registers
Addresses [0Ch to 11h]
The alarm register bytes are set up identical to the RTC
register bytes, except that the MSB of each byte functions as
an enable bit (enable = “1”). These enable bits specify which
alarm registers (seconds, minutes, etc) are used to make the
comparison. Note that there is no alarm byte for year.
The alarm function works as a comparison between the
alarm registers and the RTC registers. As the RTC
advances, the alarm will be triggered once a match occurs
between the alarm registers and the RTC registers. Any one
alarm register, multiple registers, or all registers can be
enabled for a match.
There are two alarm operation modes: Single Event and
periodic Interrupt Mode:
Single Event Mode is enabled by setting the ALME bit to
“1”, the IM bit to “0”, and disabling the frequency output.
This mode permits a one-time match between the alarm
registers and the RTC registers. Once this match occurs,
the ALM bit is set to “1” and the IRQ output will be pulled
low and will remain low until the ALM bit is reset. This can
be done manually or by using the auto-reset feature.
Interrupt Mode is enabled by setting the ALME bit to “1”,
the IM bit to “1”, and disabling the frequency output. The
IRQ output will now be pulsed each time an alarm occurs.
This means that once the interrupt mode alarm is set, it
will continue to alarm for each occurring match of the
alarm and present time. This mode is convenient for
hourly or daily hardware interrupts in microcontroller
applications such as security cameras or utility meter
reading.
To clear an alarm, the ALM bit in the status register must be
set to “0” with a write. Note that if the ARST bit is set to 1
(address 07h, bit 7), the ALM bit will automatically be cleared
when the status register is read.
BMATR1
BMATR0
DELTA
CAPACITANCE
(CBAT TO CVDD)
0
0pF
0
1
-0.5pF (
≈ +2ppm)
1
0
+0.5pF (
≈ -2ppm)
1
+1pF (
≈ -4ppm)
C
X
16 b5
8b4
4 b3
2b2
1 b1
0.5b0
9
+
+
+
+
+
+
()pF
=
C
LOAD
1
C
X1
-----------
1
C
X2
-----------
+
-----------------------------------
=
C
LOAD
16 b5
8 b4
4 b3
2 b2
1 b1
0.5 b0
9
+
+
+
+
+
+
2
-----------------------------------------------------------------------------------------------------------------------------
pF
=
TABLE 5. DIGITAL TRIMMING REGISTERS
DTR REGISTER
ESTIMATED
FREQUENCY
PPM
DTR2
DTR1
DTR0
0
0 (default)
001
+20
010
+40
011
+60
100
0
101
-20
110
-40
111
-60
ISL1218
相關PDF資料 |
PDF描述 |
|---|---|
| ISL1208IRT8Z | IC RTC/CALENDER I2C 8-TDFN |
| ISL1208IRT8Z-TK | IC RTC/CALENDER I2C 8-TDFN |
| VI-JV2-MZ | CONVERTER MOD DC/DC 15V 25W |
| VI-JV1-MZ | CONVERTER MOD DC/DC 12V 25W |
| ISL12058IBZ | IC RTC/CALENDAR I2C-BUS 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL1218IUZ | 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1218IUZ-T | 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1219 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM and Event Detection |
| ISL1219IUZ | 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL1219IUZ-T | 功能描述:實時時鐘 REAL TIME CLKRTC IN RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。