- 您現在的位置：買賣IC網 > PDF目錄9262 > ISL22326UFR16Z-TK (Intersil)IC POT DGTL 128TP LN LP 16-QFN PDF資料下載
參數資料
| 型號： | ISL22326UFR16Z-TK |
| 廠商： | Intersil |
| 文件頁數： | 3/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 128TP LN LP 16-QFN |
| 標準包裝： | 1,000 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 電阻（歐姆）： | 50k |
| 電路數： | 2 |
| 溫度系數： | 標準值 ±80 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 16-QFN-EP（4x4） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
11
FN6176.2
September 8, 2009
The non-volatile IVRi and volatile WRi registers are accessible
with the same address.
The Access Control Register (ACR) contains information
and control bits described in Table 2. The VOL bit at access
control register (ACR[7]) determines whether the access is
to wiper registers WRi or initial value registers IVRi.
If VOL bit is 0, the non-volatile IVRi registers are accessible. If
VOL bit is 1, only the volatile WRi are accessible. Note, value
is written to IVRi register also is written to the corresponding
WRi. The default value of this bit is 0.
The SHDN bit (ACR[6]) disables or enables Shutdown mode.
This bit is logically ANDed with SHDN pin. When this bit is 0,
DCP is in Shutdown mode. Default value of SHDN bit is 1.
The WIP bit (ACR[5]) is read only bit. It indicates that
non-volatile write operation is in progress. It is impossible to
write to the IVRi, WRi or ACR while WIP bit is 1.
Shutdown Mode
The device can be put in Shutdown mode either by pulling the
SHDN pin to GND or setting the SHDN bit in the ACR register
to 0. The truth table for Shutdown mode is in Table 3.
I2C Serial Interface
The ISL22326 supports an I2C bidirectional bus oriented
protocol. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as the
receiver. The device controlling the transfer is a master and
the device being controlled is the slave. The master always
initiates data transfers and provides the clock for both
transmit and receive operations. Therefore, the ISL22326
operates as a slave device in all applications.
All communication over the I2C interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line must change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions
(see Figure 16). On power-up of the ISL22326, the SDA pin
is in the input mode.
All I2C interface operations must begin with a START
condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH. The ISL22326 continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition is met (see
Figure 16). A START condition is ignored during the
power-up of the device.
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while
SCL is HIGH (see Figure 16). A STOP condition at the end
of a read operation, or at the end of a write operation places
the device in its standby mode.
An ACK, Acknowledge, is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (see Figure 17).
The ISL22326 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
ISL22326 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation.
A valid Identification Byte contains 1010 as the four MSBs,
and the following three bits matching the logic values present
at pins A2, A1, and A0. The LSB is the Read/Write bit. Its
value is “1” for a Read operation, and “0” for a Write operation
(see Table 4).
TABLE 4. IDENTIFICATION BYTE FORMAT
TABLE 1. MEMORY MAP
ADDRESS
NON-VOLATILE
VOLATILE
8—
ACR
7
Reserved
6
5
4
3
2
General Purpose
Not Available
1
0
IVR1
IVR0
WR1
WR0
TABLE 2. ACCESS CONTROL REGISTER (ACR)
VOL
SHDN
WIP
00000
TABLE 3.
SHDN pin
SHDN bit
Mode
High
1
Normal operation
Low
Shutdown
High
0
Shutdown
Low
0
Shutdown
1010
A2
A1
A0
R/W
(MSB)
(LSB)
Logic values at pins A2, A1, and A0 respectively
ISL22326
相關PDF資料 |
PDF描述 |
|---|---|
| ISL22416UFRT10Z | IC POT DGTL 128TP LN LP 10-TDFN |
| MS27508E22B35SD | CONN RCPT 100POS BOX MNT W/SCKT |
| ISL22416WFRT10Z | IC POT DGTL 128TP LN LP 10-TDFN |
| MS3106F22-4P | CONN PLUG 4POS STRAIGHT W/PINS |
| MS27467E21B11P | CONN PLUG 11POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22326UFV14Z | 功能描述:數字電位計 IC 128 TAP FL RNG DCP 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22326UFV14Z-TK | 功能描述:數字電位計 IC 128 TAP FL RNG IND DCP 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22326WFR16Z | 功能描述:數字電位計 IC 128 TAP FL RNG DCP 16LD 4X4 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22326WFR16Z-TK | 功能描述:數字電位計 IC 128 TAP FL RNG IND DL DCP 16LD 4X4 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22326WFV14Z | 功能描述:數字電位計 IC 128 TAP FL RNG DCP 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。