參數資料
型號: ISL22326WFV14Z
廠商: Intersil
文件頁數: 5/15頁
文件大小: 0K
描述: IC POT DGTL 128TP LN LP 14-TSSOP
標準包裝: 960
系列: XDCP™
接片: 128
電阻(歐姆): 10k
電路數: 2
溫度系數: 標準值 ±50 ppm/°C
存儲器類型: 非易失
接口: I²C(設備位址)
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 14-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 14-TSSOP
包裝: 管件
13
FN6176.2
September 8, 2009
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL22326 responds with an ACK. At this time, the device
enters its standby state (see Figure 18). The device can
receive more than one byte of data by auto incrementing the
address after each received byte. Note after reaching the
address 08h, the internal pointer “rolls over” to address 00h.
The non-volatile write cycle starts after STOP condition is
determined and it requires up to 20ms delay for the next
non-volatile write. Thus, non-volatile registers must be
written individually.
Read Operation
A Read operation consist of a three byte instruction followed
by one or more Data Bytes (see Figure 19). The master
initiates the operation issuing the following sequence: a
START, the Identification byte with the R/W bit set to “0”, an
Address Byte, a second START, and a second Identification
byte with the R/W bit set to “1”. After each of the three bytes,
the ISL22326 responds with an ACK. Then the ISL22326
transmits Data Bytes as long as the master responds with an
ACK during the SCL cycle following the eighth bit of each
byte. The master terminates the read operation (issuing a
ACK and a STOP condition) following the last bit of the last
Data Byte (see Figure 19).
The Data Bytes are from the registers indicated by an
internal pointer. This pointer initial value is determined by the
Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 08h, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.
In order to read back the non-volatile IVR, it is recommended
that the application reads the ACR first to verify the WIP bit
is 0. If the WIP bit (ACR[5]) is not 0, the host should repeat
its reading sequence again.
ISL22326
相關PDF資料
PDF描述
ISL22329WFU10Z-TK IC POT DGTL 128TP LN LP 10-MSOP
ISL22343UFV20Z IC POT DGTL 256TP LN LP 20-TSSOP
ISL22346UFRT20Z IC POT DGTL 128TP LN LP 20-TQFN
ISL22349WFV14Z-TK IC POT DGTL 128TP LN LP 14-TSSOP
ISL22414WMU10Z-T7A IC DGTL POT 256POS 10K 10MSOP
相關代理商/技術參數
參數描述
ISL22326WFV14Z-TK 功能描述:數字電位計 IC 128 TAP FL RNG IND DCP 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
ISL22326WMVEP 制造商:Intersil Corporation 功能描述:V62/08604-01XE, 128 TAP MIL RANGE DUAL DCP 14LD TSSOP - Rail/Tube
ISL22326WMVEP-TK 制造商:Intersil Corporation 功能描述:DGTL POTENTIOMETER 128POS 10KOHM DUAL 14TSSOP - Tape and Reel
ISL22329 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual Digitally Controlled Potentiometers XDCP
ISL22329UFU10Z 功能描述:IC POT DGTL 128TP LN LP 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻(歐姆):50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型,TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR)