- 您現在的位置：買賣IC網 > PDF目錄9069 > ISL22349UFV14Z (Intersil)IC POT DGTL 128TP LN LP 14-TSSOP PDF資料下載
參數資料
| 型號： | ISL22349UFV14Z |
| 廠商： | Intersil |
| 文件頁數： | 13/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 128TP LN LP 14-TSSOP |
| 標準包裝： | 96 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 電阻（歐姆）： | 50k |
| 電路數： | 4 |
| 溫度系數： | 標準值 ±80 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁
9
FN6331.3
May 28, 2009
SERIAL CLOCK (SCL)
This is the serial clock input of the I2C serial interface. SCL
requires an external pull-up resistor, since it is an open drain
input.
DEVICE ADDRESS (A2 - A0)
The address inputs are used to set the least significant 3 bits
of the 7-bit I2C interface slave address. A match in the slave
address serial data stream must match with the Address
input pins in order to initiate communication with the
ISL22349. A maximum of 8 ISL22349 devices may occupy
the I2C serial bus.
Principles of Operation
The ISL22349 is an integrated circuit incorporating four
DCPs with their associated registers, non-volatile memory
and an I2C serial interface providing direct communication
between a host and the potentiometers and memory. The
resistor arrays are comprised of individual resistors
connected in series. At either end of the array and between
each resistor is an electronic switch that transfers the
potential at that point to the wiper.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions.
When the device is powered down, the last value stored in
IVRi will be maintained in the non-volatile memory. When
power is restored, the contents of the IVRi are recalled and
loaded into the corresponding WRi to set the wipers to the
initial value.
DCP Description
Each DCP is implemented with a combination of resistor
elements and CMOS switches. The physical ends of each
DCP are equivalent to the fixed terminals of a mechanical
potentiometer and internally connected to Vcc and GND.
The RW pin of each DCP is connected to intermediate
nodes, and is equivalent to the wiper terminal of a
mechanical potentiometer. The position of the wiper terminal
within the DCP is controlled by volatile Wiper Register (WR).
Each DCP has its own WR. When the WR of a DCP contains
all zeroes (WR[6:0] = 00h), its wiper terminal (RW) is closest
to GND. When the WR register of a DCP contains all ones
(WR[6:0] = 7Fh), its wiper terminal (RW) is closest to VCC.
As the value of the WR increases from all zeroes (0) to all
ones (127 decimal), the wiper moves monotonically from the
position closest to GND to the closest to VCC.
While the ISL22349 is being powered up, all four WRs are
reset to 40h (64 decimal), which locates RW roughly at the
center between GND and VCC. After the power supply
voltage becomes large enough for reliable non-volatile
memory reading, all WRs will be reload with the value stored
in corresponding non-volatile Initial Value Registers (IVRs).
The WRs can be read or written to directly using the I2C
serial interface as described in the following sections. The
I2C interface Address Byte has to be set to 00h, 01h, 02h or
03h to access the WR of DCP0, DCP1, DCP2 or DCP3
respectively.
Memory Description
The ISL22349 contains seven non-volatile and five volatile
8-bit registers. The memory map of ISL22349 is on Table 1.
The four non-volatile registers (IVRi) at address 0, 1, 2 and
3, contain initial wiper value and volatile registers (WRi)
contain current wiper position. In addition, three non-volatile
General Purpose registers from address 4 to address 6 are
available.
The non-volatile IVRi and volatile WRi registers are
accessible with the same address.
The Access Control Register (ACR) contains information
and control bits described below in Table 2. The VOL bit at
access control register (ACR[7]) determines whether the
access is to wiper registers WRi or initial value registers
IVRi.
If VOL bit is 0, the non-volatile IVRi registers are accessible.
If VOL bit is 1, only the volatile WRi are accessible. Note,
value is written to IVRi register also is written to the
corresponding WRi. The default value of this bit is 0.
The SHDN bit (ACR[6]) disables or enables Shutdown
mode. This bit is logically AND with SHDN pin. When this bit
is 0, DCPs are in Shutdown mode. Default value of SHDN bit
is 1.
The WIP bit (ACR[5]) is read only bit. It indicates that
non-volatile write operation is in progress. It is impossible to
write to the WRi or ACR while WIP bit is 1.
Shutdown Mode
The device can be put in Shutdown mode either by pulling the
SHDN pin to GND or setting the SHDN bit in the ACR register
TABLE 1. MEMORY MAP
ADDRESS
NON-VOLATILE
VOLATILE
8—
ACR
7
Reserved
6
5
4
General Purpose
Not Available
3
2
1
0
IVR3
IVR2
IVR1
IVR0
WR3
WR2
WR1
WR0
TABLE 2. ACCESS CONTROL REGISTER (ACR)
VOL
SHDN
WIP
00000
ISL22349
相關PDF資料 |
PDF描述 |
|---|---|
| ISL22449UFV14Z | IC POT DGTL 128TP LN LP 14-TSSOP |
| ISL22449WFV14Z | IC POT DGTL 128TP LN LP 14-TSSOP |
| MS27472E22B2PB | CONN RCPT 85POS WALL MT W/PINS |
| MS27473E22F2PC | CONN PLUG 85POS STRAIGHT W/PINS |
| MS27473E22F2PB | CONN PLUG 85POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22349UFV14Z-TK | 功能描述:IC POT DGTL 128TP LN LP 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| ISL22349WFV14Z | 功能描述:IC POT DGTL 128TP LN LP 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| ISL22349WFV14Z-TK | 功能描述:IC POT DGTL 128TP LN LP 14-TSSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻（歐姆）:50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR) |
| ISL22414 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Single Digitally Controlled Potentiometer |
| ISL22414TFU10Z | 功能描述:數字電位計 IC 256 TAP FL RNG IND DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。