參數資料
型號: ISL22429WFU10Z
廠商: Intersil
文件頁數: 2/13頁
文件大小: 0K
描述: IC POT DGTL 128TP LN LP 10-MSOP
標準包裝: 50
系列: XDCP™
接片: 128
電阻(歐姆): 10k
電路數: 2
溫度系數: 標準值 ±50 ppm/°C
存儲器類型: 非易失
接口: 4 線 SPI(芯片選擇)
電源電壓: 2.7 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-MSOP
包裝: 管件
10
FN6332.2
May 28, 2009
SPI Serial Interface
The ISL22429 supports an SPI serial protocol, mode 0. The
device is accessed via the SDI input and SDO output with
data clocked in on the rising edge of SCK, and clocked out
on the falling edge of SCK. CS must be LOW during
communication with the ISL22429. SCK and CS lines are
controlled by the host or master. The ISL22429 operates
only as a slave device.
All communication over the SPI interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
The first byte sent to the ISL22429 from the SPI host is the
Identification Byte. A valid Identification Byte contains 0101
as the four MSBs, with the following four bits set to 0.
TABLE 4. IDENTIFICATION BYTE FORMAT
The next byte sent to the ISL22429 contains the instruction
and register pointer information. The four MSBs are the
instruction and four LSBs are register address (see Table 5).
TABLE 5. IDENTIFICATION BYTE FORMAT
There are only two valid instruction sets:
1011(binary) - is a Read operation
1100(binary) - is a Write operation
Write Operation
A Write operation to the ISL22429 is a three-byte operation.
It requires first, the CS transition from HIGH to LOW, then a
valid Identification Byte, then a valid instruction byte
following by Data Byte is sent to SDI pin. The host
terminates the write operation by pulling the CS pin from
LOW to HIGH. For a write to addresses 0000b or 0001b, the
MSB at address 8 (ACR[7]) determines if the Data Byte is to
be written to volatile or both volatile and non-volatile
Figure 12.
Device can receive more than one byte of data by auto
incrementing the address after each received byte. Note
after reaching the address 0110b, the internal pointer “rolls
over” to address 0000b.
The internal non-volatile write cycle starts after rising edge of
CS and takes up to 20ms. Thus, non-volatile registers must
be written individually.
Read Operation
A read operation to the ISL22429 is a three-byte operation. It
requires first, the CS transition from HIGH to LOW, then a
valid Identification Byte, then a valid instruction byte
following by “dummy” Data Byte is sent to SDI pin. The SPI
host reads the data from SDO pin on falling edge of SCK.
The host terminates the read operation by pulling the CS pin
from LOW to HIGH (see Figure 13).
The ISL22429 will provide the Data Bytes to the SDO pin as
long as SCK is provided by the host from the registers
indicated by an internal pointer. This pointer initial value is
determined by the register address in the Read operation
instruction, and increments by one during transmission of
each Data Byte. After reaching the memory location 0110b,
the pointer “rolls over” to 0000b, and the device continues to
output the data for each received SCK clock.
In order to read back the non-volatile IVR, it is recommended
that the application reads the ACR first to verify the WIP bit
is 0. If the WIP bit (ACR[5]) is not 0, the host should repeat
its reading sequence again.
TABLE 3.
SHDN pin
SHDN bit
Mode
High
1
Normal operation
Low
1
Shutdown
High
0
Shutdown
Low
0
Shutdown
01010000
(MSB)
(LSB)
76543210
I3
I2
I1
I0
R3
R2
R1
R0
ISL22429
相關PDF資料
PDF描述
VI-21Z-MU-S CONVERTER MOD DC/DC 2V 80W
IDT2309A-1DCGI8 IC CLK BUFFER ZD STD DRV 16-SOIC
VI-2T3-MW-S CONVERTER MOD DC/DC 24V 100W
IDT2309-1HPGG8 IC CLK BUFFER ZD HI DRV 16-TSSOP
IDT2309-1HDCGI8 IC CLK BUFFER ZD HI DRV 16-SOIC
相關代理商/技術參數
參數描述
ISL22429WFU10Z-TK 功能描述:IC POT DGTL 128TP LN LP 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻(歐姆):50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型,TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR)
ISL22444 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad Digitally Controlled Potentiometer XDCP
ISL22444TFR20Z 功能描述:數字電位計 IC 273 TAP FL RNG IND QD SPI DCP 5X5 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
ISL22444TFR20Z-TK 功能描述:數字電位計 IC 276 TAP FL RNG IND QD SPI DCP 5X5 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
ISL22444TFV20Z 功能描述:數字電位計 IC 267 TAP FL RNG IND QD SPI DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel