參數資料
| 型號： | ISL22444UFR20Z |
| 廠商： | Intersil |
| 文件頁數： | 4/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 256TP LN LP 20-QFN |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 600 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 50k |
| 電路數： | 4 |
| 溫度系數： | 標準值 ±45 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 2.25 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VQFN 裸露焊盤 |
| 供應商設備封裝： | 20-QFN 裸露焊盤（5x5） |
| 包裝： | 管件 |
12
FN6426.0
May 24, 2007
contains all zeroes (WRi[7:0]= 00h), its wiper terminal (RWi)
is closest to its “Low” terminal (RLi). When the WRi register
of a DCP contains all ones (WRi[7:0]= FFh), its wiper
terminal (RWi) is closest to its “High” terminal (RHi). As the
value of the WRi increases from all zeroes (0) to all ones
(255 decimal), the wiper moves monotonically from the
position closest to RLi to the closest to RHi. At the same
time, the resistance between RWi and RLi increases
monotonically, while the resistance between RHi and RWi
decreases monotonically.
While the ISL22444 is being powered up, the WRi is reset to
80h (128 decimal), which locates RWi roughly at the center
between RLi and RHi. After the power supply voltage
becomes large enough for reliable non-volatile memory
reading, the WRi will be reloaded with the value stored in a
non-volatile Initial Value Register (IVRi). All the IVRs are
factory programmed with 80h.
The WRi and IVRi can be read or written to directly using the
SPI serial interface as described in the following sections.
Memory Description
The ISL22444 contains four non-volatile 8-bit Initial Value
Registers (IVRi), eleven non-volatile 8-bit General Purpose
(GP) registers, four volatile 8-bit Wiper Registers (WRi), and
volatile 8-bit Access Control Register (ACR). The memory
map of ISL22444 is in Table 1.
The non-volatile registers (IVRi) at address 0, 1, 2 and 3
contain initial wiper position and volatile registers (WRi)
contain current wiper position.
The register at address 0Fh is a read-only reserved register.
Information read from this register should be ignored.
The non-volatile IVRi and volatile WRi registers are
accessible with the same address.
The Access Control Register (ACR) contains information
and control bits described below in Table 2.
The VOL bit (ACR[7]) determines whether the access to
wiper registers WRi or initial value registers IVRi.
If VOL bit is 0, the non-volatile IVRi and General Purpose
registers are accessible. If VOL bit is 1, only the volatile WRi
are accessible. Note: value that is written to IVRi register
also is written to the corresponding WRi. The default value of
this bit is 0.
The SHDN bit (ACR[6]) disables or enables Shutdown
mode. When this bit is 0, DCP is in Shutdown mode, i.e.
each DCP is forced to end-to-end open circuit and RWi is
shorted to RLi as shown on Figure 15. Default value of
SHDN bit is 1.
Setting SHDN bit to 1 is returned wipers to prior to Shutdown
Mode position.
The WIP bit (ACR[5]) is a read-only bit. It indicates that non-
volatile write operation is in progress. The WIP bit can be
read repeatedly after a non-volatile write to determine if the
write has been completed. It is impossible to write or read to
the WRi or ACR while WIP bit is 1.
The SDO bit (ACR[1]) configures type of SDO output pin.
The default value of SDO bit is 0 for Push - Pull output. SDO
pin can be configured as Open Drain output for some
application. In this case, an external pull up resistor is
required. See “Applications Information” on page 14.
SPI Serial Interface
The ISL22444 supports an SPI serial protocol, mode 0. The
device is accessed via the SDI input and SDO output with
data clocked in on the rising edge of SCK, and clocked out
TABLE 1. MEMORY MAP
ADDRESS
(hex)
NON-VOLATILE
VOLATILE
10
N/A
ACR
F
Reserved
E
General Purpose
N/A
D
General Purpose
N/A
C
General Purpose
N/A
B
General Purpose
N/A
A
General Purpose
N/A
9
General Purpose
N/A
8
General Purpose
N/A
7
General Purpose
N/A
6
General Purpose
N/A
5
General Purpose
N/A
4
General Purpose
N/A
3IVR3
WR3
2IVR2
WR2
1IVR1
WR1
0IVR0
WR0
TABLE 2. ACCESS CONTROL REGISTER (ACR)
BIT #
76
5
4
3
2
1
0
BIT
NAME
VOL SHDN WIP
0
SDO
0
RLi
RWi
RHi
FIGURE 15. DCP CONNECTION IN SHUTDOWN MODE
ISL22444
相關PDF資料 |
PDF描述 |
|---|---|
| MS27473E16A42PA | CONN PLUG 42POS STRAIGHT W/PINS |
| SY10E158JZ TR | IC MULTIPLEXER 5-BIT 2:1 28-PLCC |
| GTC030-18-20S | CONN RCPT 5POS PANEL MNT W/SCKT |
| SY100E163JZ TR | IC MULTIPLEXER 2BIT 8:1 28-PLCC |
| SY100E157JY TR | IC MULTIPLEXER QUAD 2:1 28-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22444UFR20Z-TK | 功能描述:數字電位計 IC 277 TAP FL RNG IND QD SPI DCP 5X5 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22444UFV20Z | 功能描述:數字電位計 IC 268 TAP FL RNG IND QD SPI DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22444UFV20Z-TK | 功能描述:數字電位計 IC 271 TAP FL RNG IND QD SPI DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22444WFR20Z | 功能描述:數字電位計 IC 275 TAP FL RNG IND QD SPI DCP 5X5 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22444WFR20Z-TK | 功能描述:數字電位計 IC 278 TAP FL RNG IND QD SPI DCP 5X5 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。