- 您現在的位置：買賣IC網 > PDF目錄1926 > ISL23315WFUZ-TK (Intersil)IC DGTL POT 256POS 10K 10MSOP PDF資料下載
參數資料
| 型號： | ISL23315WFUZ-TK |
| 廠商： | Intersil |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DGTL POT 256POS 10K 10MSOP |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1,000 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 10k |
| 電路數： | 1 |
| 溫度系數： | 標準值 175 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
ISL23315
15
FN7778.1
August 15, 2011
I2C Serial Interface
The ISL23315 supports an I2C bidirectional bus oriented
protocol. The protocol defines any device that sends data onto
the bus as a transmitter and the receiving device as the receiver.
The device controlling the transfer is a master and the device
being controlled is the slave. The master always initiates data
transfers and provides the clock for both transmit and receive
operations. Therefore, the ISL23315 operates as a slave device
in all applications.
All communication over the I2C interface is conducted by sending
the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line must change only during SCL LOW
periods. SDA state changes during SCL HIGH are reserved for
indicating START and STOP conditions (see Figure 27). On
power-up of the ISL23315, the SDA pin is in the input mode.
All I2C interface operations must begin with a START condition,
which is a HIGH-to-LOW transition of SDA while SCL is HIGH. The
ISL23315 continuously monitors the SDA and SCL lines for the
START condition and does not respond to any command until this
condition is met (see Figure 27). A START condition is ignored
during the power-up of the device.
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while SCL is
HIGH (see Figure 27). A STOP condition at the end of a read
operation or at the end of a write operation places the device in
its standby mode.
An ACK (Acknowledge) is a software convention used to indicate
a successful data transfer. The transmitting device, either master
or slave, releases the SDA bus after transmitting eight bits.
During the ninth clock cycle, the receiver pulls the SDA line LOW
to acknowledge the reception of the eight bits of data
(see Figure 28).
The ISL23315 responds with an ACK after recognition of a START
condition followed by a valid Identification Byte, and once again
after successful receipt of an Address Byte. The ISL23315 also
responds with an ACK after receiving a Data Byte of a write
operation. The master must respond with an ACK after receiving
a Data Byte of a read operation.
A valid Identification Byte contains 10100 as the five MSBs, and
the following two bits matching the logic values present at pins
A1 and A0. The LSB is the Read/Write bit. Its value is “1” for a
Read operation and “0” for a Write operation (see Table 3).
TABLE 3. IDENTIFICATION BYTE FORMAT
FIGURE 26. SHUTDOWN MODE WIPER RESPONSE
POWER-UP
USER PROGRAMMED
MID SCALE = 80H
SHDN ACTIVATED SHDN RELEASED
AFTER SHDN
WIPE
R
VO
LT
AGE,
V
RW
(V
)
SHDN MODE
TIME (s)
WIPER RESTORE TO
THE ORIGINAL POSITION
0
10100
A1
A0
R/W
(MSB)
(LSB)
LOGIC VALUES AT PINS A1 AND A0, RESPECTIVELY
SDA
SCL
START
DATA
STOP
STABLE
CHANGE
DATA
STABLE
FIGURE 27. VALID DATA CHANGES, START AND STOP CONDITIONS
相關PDF資料 |
PDF描述 |
|---|---|
| ISL23318WFUZ-TK | IC DGTL POT 1CH 10K 10MSOP |
| ISL23325WFVZ-T7A | IC DGTL POT DUAL 10K 14TSSOP |
| ISL23328WFVZ-T7A | IC DGTL POT 2CH 10K 14TSSOP |
| ISL23345UFRZ | IC DGTL POT QUAD 50K 20QFN |
| ISL23348UFVZ | IC DGTL POT 4CH 50K 20TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL23318TFRUZ-T7A | 功能描述:數字電位計 IC 128 TAPVOLATILE I2C SNG RNG IND DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23318TFRUZ-TK | 功能描述:數字電位計 IC 128 TAP VOLATILE I2C SINGLE FL DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23318TFUZ | 功能描述:數字電位計 IC 128 TAP VOLATILE I2C SINGLE FL DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23318TFUZ-T7A | 功能描述:數字電位計 IC 128 TAPVOLATILE I2C SNG RNG IND DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23318TFUZ-TK | 功能描述:數字電位計 IC 128 TAP VOLATILE I2C SINGLE FL DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。