- 您現在的位置：買賣IC網 > PDF目錄17647 > ISL23325WFVZ (Intersil)IC DGTL POT 256POS 10K 14TSSOP PDF資料下載
參數資料
| 型號： | ISL23325WFVZ |
| 廠商： | Intersil |
| 文件頁數： | 7/20頁 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 256POS 10K 14TSSOP |
| 標準包裝： | 960 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 10k |
| 電路數： | 2 |
| 溫度系數： | 標準值 125 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | * |
| 封裝/外殼： | * |
| 供應商設備封裝： | * |
| 包裝： | * |
ISL23325
15
FN7870.0
June 21, 2011
I2C Serial Interface
The ISL23325 supports an I2C bidirectional bus oriented
protocol. The protocol defines any device that sends data onto
the bus as a transmitter and the receiving device as the receiver.
The device controlling the transfer is a master and the device
being controlled is the slave. The master always initiates data
transfers and provides the clock for both transmit and receive
operations. Therefore, the ISL23325 operates as a slave device
in all applications.
All communication over the I2C interface is conducted by sending
the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line must change only during SCL LOW
periods. SDA state changes during SCL HIGH are reserved for
indicating START and STOP conditions (see Figure 27). On
power-up of the ISL23325, the SDA pin is in the input mode.
All I2C interface operations must begin with a START condition,
which is a HIGH-to-LOW transition of SDA while SCL is HIGH. The
ISL23325 continuously monitors the SDA and SCL lines for the
START condition and does not respond to any command until this
condition is met (see Figure 27). A START condition is ignored
during the power-up of the device.
All I2C interface operations must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA while SCL is
HIGH (see Figure 27). A STOP condition at the end of a read
operation or at the end of a write operation places the device in
its standby mode.
An ACK (Acknowledge) is a software convention used to indicate
a successful data transfer. The transmitting device, either master
or slave, releases the SDA bus after transmitting eight bits.
During the ninth clock cycle, the receiver pulls the SDA line LOW
to acknowledge the reception of the eight bits of data
(see Figure 28).
The ISL23325 responds with an ACK after recognition of a START
condition followed by a valid Identification Byte, and once again
after successful receipt of an Address Byte. The ISL23325 also
responds with an ACK after receiving a Data Byte of a write
operation. The master must respond with an ACK after receiving
a Data Byte of a read operation.
A valid Identification Byte contains 1010 as the four MSBs, and
the following three bits are matching the logic values present at
pins A2, A1 and A0. The LSB is the Read/Write bit. Its value is “1”
for a Read operation and “0” for a Write operation (see Table 3).
TABLE 3. IDENTIFICATION BYTE FORMAT
FIGURE 26. SHUTDOWN MODE WIPER RESPONSE
POWER-UP
USER PROGRAMMED
MID SCALE = 80H
SHDN ACTIVATED SHDN RELEASED
AFTER SHDN
WI
PER
VO
LT
AGE,
V
RW
(V)
SHDN MODE
TIME (s)
WIPER RESTORE TO
THE ORIGINAL POSITION
0
1010
A2
A1
A0
R/W
(MSB)
(LSB)
LOGIC VALUES AT PINS A2, A1 AND A0 RESPECTIVELY
SDA
SCL
START
DATA
STOP
STABLE
CHANGE
DATA
STABLE
FIGURE 27. VALID DATA CHANGES, START AND STOP CONDITIONS
相關PDF資料 |
PDF描述 |
|---|---|
| LB15SKW01-05-CJ | SWITCH PUSHBUTTON SPDT 3A 125V |
| LB15SKW01-12-BJ | SWITCH PUSHBUTTON SPDT 3A 125V |
| ISL23325UFVZ | IC DGTL POT 256POS 50K 14TSSOP |
| TM7EW502 | TRIMMER 5K OHM 0.5W TH |
| ISL84053IVZ | IC MULTIPLEXER TRPL 2X1 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL23325WFVZ-T7A | 功能描述:數字電位計 IC 256 TAPVOLATILE I2C DUAL FL RNG IND 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23325WFVZ-TK | 功能描述:數字電位計 IC 256 TAP VOLATILE I2C DL FL RNG DCP 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23328 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual, 128-Tap, Low Voltage Digitally Controlled Potentiometer (XDCPa?￠) |
| ISL23328TFRUZ-T7A | 功能描述:數字電位計 IC 128 TAPVOLATILE I2C DUAL RNG IND 16LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23328TFRUZ-TK | 功能描述:數字電位計 IC 128 TAP VOLATILE I2C DL FL RNG DCP 16LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。