14 FN7901.0 August 3, 2011 In shutdown mode, the RW terminal is shorted to the RL terminal with around 2k resistance, as shown in Figu" />
參數資料
型號: ISL23418UFUZ
廠商: Intersil
文件頁數: 6/20頁
文件大?。?/td> 0K
描述: IC DGTL POT 1CH 50K 10MSOP
標準包裝: 1,000
系列: XDCP™
接片: 128
電阻(歐姆): 50k
電路數: 1
溫度系數: 標準值 85 ppm/°C
存儲器類型: 易失
接口: 4 線 SPI(芯片選擇)
電源電壓: 1.2 V ~ 5.5 V,1.7 V ~ 5.5 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 10-TFSOP,10-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 10-MSOP
包裝: 管件
ISL23418
14
FN7901.0
August 3, 2011
In shutdown mode, the RW terminal is shorted to the RL terminal
with around 2k resistance, as shown in Figure 25. When the device
enters shutdown, all current DCP WR settings are maintained. When
the device exits shutdown, the wipers return to the previous WR
settings after a short settling time (Figure 26).
In shutdown mode, if there is a glitch in the power supply that
causes it to drop below 1.3V for more than 0.2s to 0.4s, the
wipers are RESET to their mid position. This is done to avoid an
undefined state at the wiper outputs.
SPI Serial Interface
The ISL23418 supports an SPI serial protocol, mode 0. The
device is accessed via the SDI input and SDO output, with data
clocked in on the rising edge of SCK and clocked out on the
falling edge of SCK. CS must be LOW during communication with
the ISL23418. The SCK and CS lines are controlled by the host or
master. The ISL23418 operates only as a slave device. All
communication over the SPI interface is conducted by sending
the MSB of each byte of data first.
Protocol Conventions
The SPI protocol contains an Instruction Byte followed by one or
more Data Bytes. A valid Instruction Byte contains instruction as
the three MSBs, with the following five register address bits
(Table 3). The next byte sent to the ISL23418 is the Data Byte.
Table 4 contains a valid instruction set for ISL23418. If the
[R4:R0] bits are zero, then the read or write is to the WR register. If
the [R4:R0] bits are 10000, then the operation is to the ACR.
Write Operation
A write operation to the ISL23418 is a two or more bytes
operation. It first requires CS to transition from HIGH to LOW.
Then the host sends a valid Instruction Byte to the SDI pin,
followed by one or more Data Bytes. The host terminates the
write operation by pulling the CS pin from LOW to HIGH. The
instruction is executed on the rising edge of CS (Figure 27).
Read Operation
A read operation to the ISL23418 is a four-byte operation. First,
the CS transitions from HIGH to LOW. Then the host sends a valid
Instruction Byte to the SDI pin, followed by a “dummy” Data Byte,
an NOP Instruction Byte, and another “dummy” Data Byte. The
SPI host receives the Instruction Byte (instruction code + register
address) and the requested Data Byte from the SDO pin on the
rising edge of SCK during the third and fourth bytes, respectively.
The host terminates the read by pulling the CS pin from LOW to
HIGH (Figure 28).
FIGURE 25. DCP CONNECTION IN SHUTDOWN MODE
2k
RW
RL
RH
POWER-UP
USER PROGRAMMED
MID SCALE = 40H
SHDN ACTIVATED SHDN RELEASED
AFTER SHDN
WIP
E
R
VOL
TAGE
,V
RW
(V
)
SHDN MODE
TIME (s)
WIPER RESTORE TO
ORIGINAL POSITION
0
FIGURE 26. SHUTDOWN MODE WIPER RESPONSE
TABLE 3. INSTRUCTION BYTE FORMAT
BIT #
7
654321
0
I2
I1
I0
R4
R3
R2
R1
R0
TABLE 4. INSTRUCTION SET
INSTRUCTION SET
OPERATION
I2
I1
I0
R4
R3
R2
R1
R0
0
XXX
XX
NOP
0
1
XXX
XX
ACR READ
0
1
XXX
XX
ACR WRTE
1
0
R4R3R2R1R0
WR or ACR READ
1
0
R4R3R2R1R0
WR or ACR WRTE
where “X” means “do not care.”
相關PDF資料
PDF描述
VE-2T3-MW CONVERTER MOD DC/DC 24V 100W
DS1110E-60+ IC DELAY LINE 10TAP 14-TSSOP
DS1110E-125+ IC DELAY LINE 10TAP 14-TSSOP
DS1110E-100+ IC DELAY LINE 10TAP 14-TSSOP
ISL23318UFRUZ-TK IC DGTL POT 1CH 50K 10UTQFN
相關代理商/技術參數
參數描述
ISL23418UFUZ-T7A 功能描述:數字電位計 IC 128 TAPVOLATILE SPI SNG RNG IND DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
ISL23418UFUZ-TK 功能描述:數字電位計 IC 128 TAP VOLATILE SPI SINGLE DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
ISL23418WFRUZ-T7A 功能描述:數字電位計 IC 128 TAPVOLATILE SPI SNG RNG IND DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
ISL23418WFRUZ-TK 功能描述:數字電位計 IC 128 TAP VOLATILE SPI SINGLE DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
ISL23418WFUZ 功能描述:數字電位計 IC 128 TAP VOLATILE SPI SINGLE DCP 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel