- 您現在的位置：買賣IC網 > PDF目錄9419 > ISL23448TFVZ-T7A (Intersil)IC DGTL POT 4CH 100K 20TSSOP PDF資料下載
參數資料
| 型號： | ISL23448TFVZ-T7A |
| 廠商： | Intersil |
| 文件頁數： | 6/21頁 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 4CH 100K 20TSSOP |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1 |
| 系列： | XDCP™ |
| 接片： | 128 |
| 電阻（歐姆）： | 100k |
| 電路數： | 4 |
| 溫度系數： | 標準值 45 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 標準包裝 |
| 其它名稱： | ISL23448TFVZ-T7ADKR |
ISL23448
14
FN7905.0
August 19, 2011
SERIAL DATA OUTPUT (SDO)
The SDO is a serial data output pin. During a read cycle, the data
bits are shifted out on the falling edge of the serial clock SCK and
will be available to the master on the following rising edge of SCK.
The output type is configured through ACR[1] bit for Push-Pull or
Open Drain operation. The default setting for this pin is Push-Pull.
An external pull-up resistor is required for Open Drain output
operation. When CS is HIGH, the SDO pin is in tri-state (Z) or
high-tri-state (Hi-Z) depending on the selected configuration.
CHIP SELECT (CS)
CS LOW enables the ISL23448, placing it in the active power
mode. A HIGH to LOW transition on CS is required prior to the
start of any operation after power-up. When CS is HIGH, the
ISL23448 is deselected and the SDO pin is at high impedance,
and the device will be in the standby state.
VLOGIC
Digital power source for the logic control section. It supplies an
internal level translator for 1.2V to 5.5V serial bus operation. Use
the same supply as the SPI logic source.
Principles of Operation
The ISL23448 is an integrated circuit incorporating four DCPs
with its associated registers and an SPI serial interface providing
direct communication between a host and the potentiometer.
The resistor array is comprised of individual resistors connected
in series. At either end of the array and between each resistor is
an electronic switch that transfers the potential at that point to
the wiper.
The electronic switches on the device operate in a
“make-before-break” mode when the wiper changes tap
positions.
Voltage at any of the DCP pins, RHi, RLi or RWi, should not
exceed VCC level at any conditions during power-up and normal
operation.
The VLOGIC pin is the terminal for the logic control digital power
source. It should use the same supply as the SPI logic source,
which allows reliable communication with a wide range of
microcontrollers and is independent from the VCC level. This is
extremely important in systems where the master supply has
lower levels than the DCP analog supply.
DCP Description
Each DCP is implemented with a combination of resistor elements
and CMOS switches. The physical ends of each DCP are equivalent
to the fixed terminals of a mechanical potentiometer (RHi and RLi
pins). The RWi pin of the DCP is connected to intermediate nodes,
and is equivalent to the wiper terminal of a mechanical
potentiometer. The position of the wiper terminal within the DCP is
controlled by an 8-bit volatile Wiper Register (WRi). When the WR of
a DCP contains all zeroes (WRi[7:0] = 00h), its wiper terminal (RWi)
is closest to its “Low” terminal (RLi). When the WRi register of a DCP
contains all ones (WRi[7:0] = 7Fh), its wiper terminal (RWi) is closest
to its “High” terminal (RHi). As the value of the WRi increases from
all zeroes (0) to all ones (127 decimal), the wiper moves
monotonically from the position closest to RLi to the position closest
to RHi. At the same time, the resistance between RWi and RLi
increases monotonically, while the resistance between RHi and RWi
decreases monotonically.
While the ISL23448 is being powered up, all the WRi are reset to
40h (64 decimal), which positions RWi at the center between RLi
and RHi.
The WRi can be read or written to directly using the SPI serial
interface as described in the following sections.
Memory Description
The ISL23448 contains five volatile 8-bit registers: Wiper Register
WR0, Wiper Register WR1, Wiper Register WR2, Wiper Register
WR3 and Access Control Register (ACR). The memory map of
ISL23448 is shown in Table 1. The Wiper Register WRi at address i,
contains current wiper position of DCPi (i = 0, 1, 2, 3). The Access
Control Register (ACR) at address 10h contains information and
control bits described in Table 2.
The SDO bit (ACR[1]) configures the type of SDO output pin. The
default value of SDO bit is 0 for Push-Pull output. The SDO pin
can be configured as Open Drain output for some applications. In
this case, an external pull-up resistor is required. Reference the
“Serial Interface Specification” on page 7.
Shutdown Function
The SHDN bit (ACR[6]) disables or enables shutdown mode for all
DCP channels simultaneously. When this bit is 0, i.e., each DCP is
forced to end-to-end open circuit and each RW shorted to RL
through a 2k serial resistor, as shown in Figure 25. The default
value of the SHDN bit is 1.
TABLE 1. MEMORY MAP
ADDRESS
(hex)
VOLATILE
REGISTER NAME
DEFAULT SETTING
(hex)
10
ACR
40
3WR3
40
2WR2
40
1WR1
40
0WR0
40
TABLE 2. ACCESS CONTROL REGISTER (ACR)
BIT #
7
6
5
4
32
10
NAME/
VALUE
0SHDN
00
0
SDO
0
FIGURE 25. DCP CONNECTION IN SHUTDOWN MODE
2k
RW
RL
RH
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B2V-MY-F4 | CONVERTER MOD DC/DC 5.8V 50W |
| VE-B2V-MY-F3 | CONVERTER MOD DC/DC 5.8V 50W |
| ISL23448WFRZ-T7A | IC DGTL POT 4CH 10K 20QFN |
| MS3450L20-14PW | CONN RCPT 5POS WALL MNT W/PINS |
| MS3450L20-14P | CONN RCPT 5POS WALL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL23448TFVZ-TK | 功能描述:數字電位計 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23448UFRZ | 功能描述:數字電位計 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23448UFRZ-T7A | 功能描述:數字電位計 IC 128 TAPVOLATILE SPI QUAD RNG IND 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23448UFRZ-TK | 功能描述:數字電位計 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23448UFVZ | 功能描述:數字電位計 IC 128 TAP VOLATILE SPI QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。