- 您現在的位置：買賣IC網 > PDF目錄383129 > ISL23710UIU10Z (INTERSIL CORP) Terminal Voltage +-3V or +-5V, 128 Taps Up/Down Interface PDF資料下載
參數資料
| 型號： | ISL23710UIU10Z |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Terminal Voltage +-3V or +-5V, 128 Taps Up/Down Interface |
| 中文描述： | 50K DIGITAL POTENTIOMETER, INCREMENT/DECREMENT CONTROL INTERFACE, 128 POSITIONS, PDSO10 |
| 封裝： | ROHS COMPLIANT, PLASTIC, MO-187BA, MSOP-10 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 232K |
| 代理商： | ISL23710UIU10Z |
6
FN6126.0
August 22, 2005
AC Timing
Power Up and Down Requirements
In order to prevent unwanted tap position changes, bring the
CS and INC high before or concurrently with the V
CC
pin on
power-up. The potentiometer voltages must be applied after
this sequence is completed. During power-up, the data sheet
parameters for the DCP do not fully apply until 1ms after
V
CC
reaches its final value. The wiper will be set to its initial
value (64d) once V
CC
exceeds V
POR
.
Pin Descriptions
R
H
and R
L
The high (R
H
) and low (R
L
) terminals of the ISL23710 are
equivalent to the fixed terminals of a mechanical
potentiometer. The terminology of R
L
and R
H
references the
relative position of the terminal in relation to wiper movement
direction selected by the U/D input and not the voltage
potential on the terminal.
R
W
R
w
is the wiper terminal and is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the control inputs.
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the counter is incriminated or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the
counter in the direction indicated by the logic level on the
U/D input.
Chip Select (CS)
The device is selected when the CS input is LOW.
Principles of Operation
There are three sections of the ISL23710: the input control,
counter and decode section, and the resistor array. The input
control section operates just like an up/down counter. The
output of this counter is decoded to turn on a single
electronic switch connecting a point on the resistor array to
the wiper output. The resistor array is comprised of 127
individual resistors connected in series. At either end of the
array and between each resistor is an electronic switch that
transfers the potential at that point to the wiper.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions. If
the wiper is moved several positions, multiple taps are
connected to the wiper for t
IW
(INC to V
W
change). The
R
TOTAL
value for the device can temporarily be reduced by
a significant amount if the wiper is moved several positions.
Instructions and Programming
The INC, U/D and CS inputs control the movement of the
wiper along the resistor array. With CS set LOW the device
is selected and enabled to respond to the U/D and INC
inputs. HIGH to LOW transitions on INC will increment or
decrement (depending on the state of the U/D input) a seven
bit counter. The output of this counter is decoded to select
CS
INC
U/D
R
W
t
CI
t
IL
t
IH
t
CYC
t
ID
t
DI
t
IW
MI
(3)
t
ICL
t
F
t
R
10%
90%
90%
ISL23710
相關PDF資料 |
PDF描述 |
|---|---|
| ISL23710WIU10Z | Terminal Voltage +-3V or +-5V, 128 Taps Up/Down Interface |
| ISL23710 | Terminal Voltage +-3V or +-5V, 128 Taps Up/Down Interface |
| ISL23711UIU10Z | Terminal Voltage +-3V or +-5V, 128 Taps IC Serial Interface |
| ISL23711WIU10Z | Terminal Voltage +-3V or +-5V, 128 Taps IC Serial Interface |
| ISL23711 | Terminal Voltage +-3V or +-5V, 128 Taps IC Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL23710UIU10Z-T | 功能描述:數字電位計 IC ISL23710U IND 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23710WIU10Z | 功能描述:數字電位計 IC ISL23710W IND 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23710WIU10Z-T | 功能描述:數字電位計 IC ISL23710W IND 10LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23711 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Terminal Voltage +-3V or +-5V, 128 Taps IC Serial Interface |
| ISL23711UIU10Z | 功能描述:數字電位計 IC ISL23711U DCP 50KOHM SISTANCE OPT IND RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。