參數資料
型號: ISL28136FHZ-T7A
廠商: Intersil
文件頁數: 3/14頁
文件大?。?/td> 0K
描述: IC OPAMP SGL RRIO 5MHZ SOT23-6
產品培訓模塊: Solutions for Industrial Control Applications
標準包裝: 1
放大器類型: 通用
電路數: 1
輸出類型: 滿擺幅
轉換速率: 1.9 V/µs
增益帶寬積: 5MHz
-3db帶寬: 13MHz
電流 - 輸入偏壓: 16nA
電壓 - 輸入偏移: 10µV
電流 - 電源: 900µA
電流 - 輸出 / 通道: 56mA
電壓 - 電源,單路/雙路(±): 2.5 V ~ 5.5 V,±1.25 V ~ 2.75 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: SOT-23-6
供應商設備封裝: SOT-23-6
包裝: 標準包裝
產品目錄頁面: 1234 (CN2011-ZH PDF)
其它名稱: ISL28136FHZ-T7ADKR
11
FN6153.6
January 16, 2014
Applications Information
Introduction
The ISL28136 is a single channel Bi-CMOS rail-to-rail input,
output (RRIO) micropower precision operational amplifier.
The part is designed to operate from a single supply 2.4V to
5.5V. The part has an input common mode range that
extends 0.25V above the positive rail and down to the
negative supply rail. The output operation can swing within
about 3mV of the supply rails with a 100k
Ω load.
Rail-to-Rail Input
Many rail-to-rail input stages use two differential input pairs; a
long-tail PNP (or PFET) and an NPN (or NFET). Severe
penalties have to be paid for this circuit topology. As the input
signal moves from one supply rail to another, the operational
amplifier switches from one input pair to the other causing
drastic changes in input offset voltage and an undesired
change in magnitude and polarity of input offset current.
The ISL28136 achieves input rail-to-rail operation without
sacrificing important precision specifications and degrading
distortion performance. The device’s input offset voltage
exhibits a smooth behavior throughout the entire common-
mode input range. The input bias current versus the
common-mode voltage range gives an undistorted behavior
from typically down to the negative rail to 0.25V higher than
the positive rail.
Rail-to-Rail Output
The output stage uses drain-connected N and P-channel
MOSFETs to achieve rail-to-rail output swing. The P-channel
device sources current to swing the output in the positive
direction and the N-channel sinks current to swing the output
in the negative direction. The ISL28136 with a 100k
Ω load will
swing to within 3mV of the positive supply rail and within 3mV
of the negative supply rail.
Results of Over-Driving the Output
Caution should be used when over-driving the output for long
periods of time. Over-driving the output can occur in two ways.
1) The input voltage times the gain of the amplifier exceeds the
supply voltage by a large value or, 2) the output current
required is higher than the output stage can deliver. These
conditions can result in a shift in the Input Offset Voltage (VOS)
as much as 1V/hr. of exposure under these conditions.
IN+ and IN- Input Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails. They also contain
back-to-back diodes across the input terminals (see “Pin
Descriptions” on page 10 - Circuit 1). For applications where
the input differential voltage is expected to exceed 0.5V, an
external series resistor must be used to ensure the input
currents never exceed 5mA (Figure 38).
Enable/Disable Feature
The ISL28136 offers an EN pin that disables the device
when pulled up to at least 2.0V. In the disabled state (output
in a high impedance state), the part consumes typically 10A
at room temperature. By disabling the part, multiple
ISL28136 parts can be connected together as a MUX. In this
configuration, the outputs are tied together in parallel and a
channel can be selected by the EN pin. The loading effects
of the feedback resistors of the disabled amplifier must be
considered when multiple amplifier outputs are connected
together. Note that feed through from the IN+ to IN- pins
occurs on any Mux Amp disabled channel where the input
differential voltage exceeds 0.5V (e.g., active channel
VOUT = 1V, while disabled channel VIN = GND), so the mux
implementation is best suited for small signal applications. If
large signals are required, use series IN+ resistors, or a
large value RF, to keep the feed through current low enough
to minimize the impact on the active channel.
page 11 for more details.
To disable the part, the user needs to supply the 1.5A
required to pull the EN pin to the V+ rail. If left open, the EN
pin will pull to the negative rail and the device will be enabled
by default. If the EN function is not required (no need to turn
the part off), as a precaution, it is recommended that the
user tie the EN pin to the V- pin.
Limitations of the Differential Input Protection
If the input differential voltage is expected to exceed 0.5V, an
external current limiting resistor must be used to ensure the
input current never exceeds 5mA. For non-inverting unity gain
applications, the current limiting can be via a series IN+ resistor,
or via a feedback resistor of appropriate value. For other gain
configurations, the series IN+ resistor is the best choice, unless
the feedback (RF) and gain setting (RG) resistors are both
sufficiently large to limit the input current to 5mA.
Large differential input voltages can arise from several
sources:
1. During open loop (comparator) operation. Used this way,
the IN+ and IN- voltages don’t track, so differentials arise.
2. When the amplifier is disabled but an input signal is still
present. An RL or RG to GND keeps the IN- at GND, while
the varying IN+ signal creates a differential voltage. Mux
Amp applications are similar, except that the active
channel VOUT determines the voltage on the IN- terminal.
FIGURE 38. INPUT CURRENT LIMITING
-
+
RIN
RL
VIN
VOUT
ISL28136
相關PDF資料
PDF描述
68016-413HLF CONN HEADER 13POS R/A .100 TIN
TMM-141-01-S-S-SM CONN HEADER 41POS SNGL 2MM SMD
OP27EN8 IC OPAMP LOW NOISE HI-SPD 8-DIP
929665-04-19-I CONN HEADER .100 DUAL STR 38POS
TSW-147-23-S-D CONN HEADER 94POS .100" DL GOLD
相關代理商/技術參數
參數描述
ISL28138 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:4.5MHz, Single and Dual Precision Rail-to-Rail Input-Output (RRIO) Op Amps with Very Low Input Bias Current
ISL28138EVAL1Z 功能描述:EVALUATION BOARD FOR ISL28138 RoHS:是 類別:編程器,開發系統 >> 評估板 - 運算放大器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
ISL28138FBZ 功能描述:IC OPAMP SGL/DUAL 4.5MHZ 8-SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 5.5 V,±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR
ISL28138FBZ-T7 功能描述:IC OPAMP SGL/DUAL 4.5MHZ 8-SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 5.5 V,±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR
ISL28138FHZ-T7 功能描述:IC OPAMP SGL/DUAL 4.5MHZ SOT23-6 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 5.5 V,±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR