14 FN6633.6 December 16, 2010 Applications Information Functional Description The ISL28127 and ISL28227 are single and dual," />
參數資料
型號: ISL28227FUBZ-T7
廠商: Intersil
文件頁數: 6/26頁
文件大?。?/td> 0K
描述: IC OP AMP GP 10MHZ DUAL 8MSOP
標準包裝: 1,500
放大器類型: 通用
電路數: 2
轉換速率: 3.6 V/µs
增益帶寬積: 10MHz
電流 - 輸入偏壓: 1nA
電壓 - 輸入偏移: 10µV
電流 - 電源: 2.2mA
電流 - 輸出 / 通道: 45mA
電壓 - 電源,單路/雙路(±): 4.5 V ~ 40 V,±2.25 V ~ 20 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 8-TSSOP,8-MSOP(0.118",3.00mm 寬)
供應商設備封裝: 8-MSOP
包裝: 帶卷 (TR)
ISL28127, ISL28227
14
FN6633.6
December 16, 2010
Applications Information
Functional Description
The ISL28127 and ISL28227 are single and dual, low noise
10MHz BW precision op amps. Both devices are fabricated in a
new precision 40V complementary bipolar DI process. A super-
beta NPN input stage with input bias current cancellation
provides low input bias current (1nA typical), low input offset
voltage (10V typ), low input noise voltage (3nV/
√Hz), and low
1/f noise corner frequency (5Hz). These amplifiers also feature
high open loop gain (1500V/mV) for excellent CMRR (120dB)
and THD+N performance (0.0002% @ 3.5VRMS, 1kHz into 2kΩ).
A complimentary bipolar output stage enables high capacitive
load drive without external compensation.
Operating Voltage Range
The devices are designed to operate over the 4.5V (±2.25V) to
40V (±20V) range and are fully characterized at 10V (±5V) and
30V (±15V). Parameter variation with operating voltage is shown
in the “Typical Performance Curves” beginning on page 8.
Input ESD Diode Protection
The input terminals (IN+ and IN-) have internal ESD protection
diodes to the positive and negative supply rails, and an additional
anti-parallel diode pair across the inputs (see Figures 38 and 39).
For unity gain applications (see Figure 38) where the output is
connected directly to the non-inverting input a current limiting
resistor (RIN) will be needed under the following conditions to
protect the anti-parallel differential input protection diodes.
The amplifier input is supplied from a low impedance source.
The input voltage rate-of-rise (dV/dt) exceeds the maximum
slew rate of the amplifier (±3.6V/s).
If the output lags far enough behind the input, the anti-parallel
input diodes can conduct. For example, if an input pulse ramps
from 0V to +10V in 1s, then the output of the ISL28x27 will reach
only +3.6V (slew rate = 3.6V/s) while the input is at 10V, The
input differential voltage of 6.4V will force input ESD diodes to
conduct, dumping the input current directly into the output stage
and the load. The resulting current flow can cause permanent
damage to the ESD diodes. The ESD diodes are rated to 20mA,
and in the previous example, setting RIN to 1k resistor (see Figure
38) would limit the current to < 6.4mA, and provide additional
protection up to ±20V at the input.
In applications where one or both amplifier input terminals are at
risk of exposure to high voltage, current limiting resistors may be
needed at each input terminal (see Figure 39 RIN+, RIN-) to limit
current through the power supply ESD diodes to 20mA.
Output Current Limiting
The output current is internally limited to approximately ±45mA
at +25°C and can withstand an short circuit to either rail as long
as the power dissipation limits are not exceeded. This applies to
only 1 amplifier at a time for the dual op amp. Continuous
operation under these conditions may degrade long term
reliability.
Output Phase Reversal
Output phase reversal is a change of polarity in the amplifier
transfer function when the input voltage exceeds the supply
voltage. The ISL28127 and ISL28227 are immune to output
phase reversal, even when the input voltage is 1V beyond the
supplies.
Power Dissipation
It is possible to exceed the +150°C maximum junction
temperatures under certain load and power supply conditions. It
is therefore important to calculate the maximum junction
temperature (TJMAX) for all applications to determine if power
supply voltages, load conditions, or package type need to be
modified to remain in the safe operating area. These parameters
are related using Equation 1:
where:
PDMAXTOTAL is the sum of the maximum power dissipation of
each amplifier in the package (PDMAX)
PDMAX for each amplifier can be calculated using Equation 2:
where:
TMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
PDMAX = Maximum power dissipation of 1 amplifier
VS = Total supply voltage
IqMAX = Maximum quiescent supply current of 1 amplifier
VOUTMAX = Maximum output voltage swing of the application
RL = Load resistance
FIGURE 38. INPUT ESD DIODE CURRENT LIMITING- UNITY GAIN
-
+
RIN
RL
VIN
VOUT
V+
V-
FIGURE 39. INPUT ESD DIODE CURRENT LIMITING -
DIFFERENTIAL INPUT
-
+
RIN-
RL
VIN-
VOUT
V+
V-
RIN+
VIN+
TJMAX
TMAX θJAxPDMAXTOTAL
+
=
(EQ. 1)
PDMAX
VS IqMAX VS
(
- VOUTMAX)
VOUTMAX
RL
------------------------
×
+
×
=
(EQ. 2)
相關PDF資料
PDF描述
SMBJ5.0-E3/52 TVS UNIDIRECT 600W 5.0V 10% SMB
41450-2 CONN UNINS RECPT 10-14AWG 0.250
87052-172HLF BERGSTIK II .100" DR STRAIGHT
ISL28227FBZ-T7 IC OPAMP PREC 10MHZ DL LN 8SOIC
951272-7722-AR CONN HEADER 72POS 2MM R/A SOLDER
相關代理商/技術參數
參數描述
ISL28227FUBZ-T7A 功能描述:IC OP AMP GP 10MHZ DUAL 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:75 系列:MicroAmplifier™ 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.03 V/µs 增益帶寬積:100kHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:60µV 電流 - 電源:20µA 電流 - 輸出 / 通道:5mA 電壓 - 電源,單路/雙路(±):2.3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SOIC 包裝:管件
ISL28227FUZ 功能描述:IC OPAMP PREC 10MHZ DUAL 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:75 系列:MicroAmplifier™ 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.03 V/µs 增益帶寬積:100kHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:60µV 電流 - 電源:20µA 電流 - 輸出 / 通道:5mA 電壓 - 電源,單路/雙路(±):2.3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SOIC 包裝:管件
ISL28227FUZ-T13 功能描述:IC OPAMP PREC 10MHZ DUAL 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:75 系列:MicroAmplifier™ 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.03 V/µs 增益帶寬積:100kHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:60µV 電流 - 電源:20µA 電流 - 輸出 / 通道:5mA 電壓 - 電源,單路/雙路(±):2.3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SOIC 包裝:管件
ISL28227FUZ-T7 功能描述:IC OPAMP PREC 10MHZ DL LN 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:75 系列:MicroAmplifier™ 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.03 V/µs 增益帶寬積:100kHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:60µV 電流 - 電源:20µA 電流 - 輸出 / 通道:5mA 電壓 - 電源,單路/雙路(±):2.3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC(0.154",3.90mm 寬) 供應商設備封裝:8-SOIC 包裝:管件
ISL28227FUZ-T7A 功能描述:精密放大器 ISL28227FUZ PREC LW NOISE OPERTNL AMP RoHS:否 制造商:Maxim Integrated 每芯片的通道數量: 輸入補償電壓:0.25 mV at +/- 5 V 輸入電壓范圍(最大值): 安裝風格: 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube