- 您現在的位置：買賣IC網 > PDF目錄5552 > ISL28617FVZ (Intersil)IC INSTRUMENTATION AMP 24TSSOP PDF資料下載
參數資料
| 型號： | ISL28617FVZ |
| 廠商： | Intersil |
| 文件頁數： | 6/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INSTRUMENTATION AMP 24TSSOP |
| 標準包裝： | 60 |
| 放大器類型： | 儀表 |
| 電路數： | 1 |
| 輸出類型： | 差分，滿擺幅 |
| 轉換速率： | 4 V/µs |
| -3db帶寬： | 5.5MHz |
| 電流 - 輸入偏壓： | 200pA |
| 電壓 - 輸入偏移： | 30µV |
| 電流 - 電源： | 2.05mA |
| 電流 - 輸出 / 通道： | 45mA |
| 電壓 - 電源，單路/雙路(±)： | 8 V ~ 40 V，±4 V ~ 20 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
ISL28617
14
FN6562.1
October 17, 2013
2. Designing with the ISL28617
To complete a working design, the following procedure is
recommended and explained in this section:
1. Define the output voltage swing
2. Set the feedback resistor value, RFB
3. Set the input gain resistor value, RIN
3. Set the VCO, VEO power supply voltages
4. Set the VCC and VEE supply voltages
The gain of the instrumentation amplifier is set by the resistor
VCO and VEO supply power to the rail-to-rail output stage and
define the maximum output voltage swing at the ±VOUT
différentiel output pins. Power supply pins VCC and VEE power the
feedback amplifiers which, require an additional ±3V beyond the
VCO and VEO voltages to maintain linear operation of the
feedback GM stage.
Setting the Feedback Gain Resistor RFB
Resistor RFB defines the maximum differential voltage at output
terminals +VOUT to -VOUT. External resistor RFB and the differential
100A current sources define the maximum dynamic range of
the feedback stage, which defines the maximum differential
output swing of the output stage. Overload circuitry allows
>100A to flow through RFB to maintain feedback, but linearity is
degraded. Therefore, it is a good practice to keep the maximum
linear dynamic range to within ±80% of the maximum I*R across
the resistor.
In cases where large pulse overshoot is expected, the maximum
current in Equation 8 could be reduced to 50% for additional
margin (see “AC Performance Considerations” on page 16) The
penalty for increasing the feedback resistor value is higher DC
offset voltage and noise.
Output voltages that exceed the maximum dynamic range of the
feedback amplifier can degrade phase margin and cause
instability. The plot in Figure 32 shows the maximum differential
output voltage swing vs. resistor value for RFB and RIN using the
80% and 50% current source levels.
Setting the Input Gain Resistor RIN
The input gain resistor RIN is scaled to the feedback resistor
according to the gain Equation 9:
The input GM stage uses the same differential current source
arrangement as the feedback stage. Therefore, the amount of
overdrive margin (50%, 80%) included in the calculation for RFB
is also included in the calculation for RIN.
Input Stage Overdrive Considerations
(Figure 33)
There are a few cases where the input stage can be over driven,
which must be considered in the application. An input signal that
exceeds the maximum dynamic range of the gain resistor RIN,
calculated previously, can cause the ESD diodes to conduct.
When this occurs, a low impedance path from the inputs to the
input gain resistor RIN will result in signal distortion.
High speed input signals that remain within the maximum
dynamic range of the input stage can cause distortion if the input
slew rate exceeds the input stage slew rate (~4V/s). When the
input slews at a faster rate than the GM stage can follow, the
voltage difference appears across the input ESD diodes from
each input and resistor RIN. When the voltage difference is large
enough to cause the diodes to conduct, the input terminals are
shunted to RIN through the 500Ω input protection resistors,
causing distortion during the rise and fall times of the transient
pulse. The distortion will last until the resistor voltage catches up
to the input voltage.
Setting the Power Supply Voltages
The ISL28617 power supplies are partitioned so that the input stage
and feedback stages are powered from a separate pair of supply
pins (VCC, VEE) than the differential output stage (VCO,VEO). This
partitioning provides the user with the ability to adapt the ISL28617
to a wide variety of input signal power sources that would not be
possible if the supplies were strapped together internally (VCC = VCO
and VEE = VEO). However, powering the input and output supplies
from unequal supplies has restrictions that are described in the next
section.
(EQ. 8)
VOUTDIFF= ±80A * RFB
FIGURE 32. RFB, RIN vs. DYNAMIC RANGE
35
30
25
20
15
10
5
0
50
100
150
200
250
300
350
400
DY
N
A
MIC
V
O
LT
AGE
RANGE
(±
V)
RFB, RIN VALUE (k)
VOUT (V) @ 80%
VOUT (V) @ 50%
(EQ. 9)
RIN = RFB/Gain
IN+
RIN
IN-
100A
+
-
+
-
VEE
500
VCC
500
ESD
PROTECTION
ESD
PROTECTION
FIGURE 33. INPUT STAGE ESD PROTECTION DIODES
A1
A2
Q1
Q2
相關PDF資料 |
PDF描述 |
|---|---|
| 951248-4620-AR-PT | CONN HEADER 48POS 2MM R/A SMD |
| 957260-2000-AR-TP | CONN HDR 60POS 2MM VERT SMT 10AU |
| 86093214009355E1LF | DIN MISCELLANEOUS |
| 68021-372H | BERGSTIK II DR RIGHT ANGLE |
| 68021-372HLF | BERGSTIK II SR RIGHT ANGLE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL28617FVZ-T13 | 功能描述:IC INSTRUMENTATION AMP 24TSSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:75 系列:MicroAmplifier™ 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.03 V/µs 增益帶寬積:100kHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:60µV 電流 - 電源:20µA 電流 - 輸出 / 通道:5mA 電壓 - 電源，單路/雙路(±):2.3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:管件 |
| ISL28617FVZ-T7 | 功能描述:IC INSTRUMENTATION AMP 24TSSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:75 系列:MicroAmplifier™ 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.03 V/µs 增益帶寬積:100kHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:60µV 電流 - 電源:20µA 電流 - 輸出 / 通道:5mA 電壓 - 電源，單路/雙路(±):2.3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:管件 |
| ISL28617FVZ-T7A | 功能描述:儀表放大器 40V Precision Amp w/Diff ADC driver RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| ISL28617SM10EV1Z | 制造商:Intersil Corporation 功能描述:ISL28617 EVAL BOARD 1 - 24LD TSSOP - ROHS COMPLIANT - Bulk 制造商:Intersil Corporation 功能描述:BOARD EVAL FOR ISL28617 制造商:Intersil 功能描述:ISL28617 EVAL |
| ISL28617SMR25EV1Z | 制造商:Intersil Corporation 功能描述:ISL28617 EVAL BOARD 1 - 24LD TSSOP - ROHS COMPLIANT - Bulk 制造商:Intersil Corporation 功能描述:BOARD EVAL FOR ISL28617 制造商:Intersil 功能描述:ISL2617 EVAL |
發布緊急采購，3分鐘左右您將得到回復。