參數資料
型號： ISL29003
廠商： Intersil Corporation
英文描述： Light-to-Digital Output Sensor with High Sensitivity, Gain Selection, Interrupt Function and I2C Interface(具有高靈敏度，增益可選，中斷功能和I2C接口的光電輸出傳感器)
中文描述： 光到數字輸出傳感器靈敏度高，增益選擇，中斷功能和I2C接口（具有高靈敏度，增益可選，中斷功能和的I2C接口的光電輸出傳感器）
文件頁數： 6/15頁
文件大?。?/td> 258K
代理商： ISL29003
6
FN7464.3
October 8, 2007
d
Command Register 00(hex)
The Read/Write command register has five functions:
(1) Enable; Bit 7. This function either resets the ADC or
enables the ADC in normal operation. A logic 0 disables
ADC to reset-mode. A logic 1 enables adc to normal
operation.
(2) ADCPD; Bit 6. This function puts the device in a power
down mode. A logic 0 puts the device in normal operation. A
logic 1 powers down the device.
(3) Timing Mode; Bit 5. This function determines whether the
integration time is done internally or externally. In Internal
Timing Mode, integration time is determined by an internal
dual speed oscillator (f
OSC
), and the n-bit (n = 4, 8, 12,16)
counter inside the ADC. In External Timing Mode, integration
time is determined by the time between two consecutive
external-sync sync_iic pulse commands.
(4) Photodiode Select Mode; Bits 3 and 2. This function
controls the mux attached to the two photodiodes. At Mode1,
the mux directs the current of Diode1 to the ADC. At Mode2,
the mux directs the current of Diode2 only to the ADC.
Mode3 is a sequential Mode1 and Mode2 with an internal
subtract function (Diode1 - Diode2).
*n = 4, 8, 12,16 depending on the number of clock cycles
function.
(5) Width; Bits 1 and 0. This function determines the number
of clock cycles per conversion. Changing the number of
clock cycles does more than just change the resolution of
the device. It also changes the integration time, which is the
period the device’s analog-to-digital (A/D) converter samples
the photodiode current signal for a lux measurement.
Control Register 01(hex)
The Read/Write control register has three functions:
(1) Interrupt flag; Bit 5. This is the status bit of the interrupt.
The bit is set to logic high when the interrupt thresholds have
been triggered, and logic low when not yet triggered. Writing
a logic low clears/resets the status bit.
(2) Range/Gain; Bits 3 and 2. The Full Scale Range can be
adjusted by an external resistor Rext and/or it can be
adjusted via I
2
C using the Gain/Range function. Gain/Range
has four possible values, Range(k) where k is 1 through 4.
Table 9 lists the possible values of Range(k) and the
resulting FSR for some typical value R
EXT
resistors.
TABLE 2. WRITE ONLY REGISTERS
ADDRESS
REGISTER
NAME
FUNCTIONS/
DESCRIPTION
b1xxx_xxxx
sync_iic
Writing a logic 1 to this address bit
ends the current adc-integration and
starts another. Used only with
External Timing Mode.
bx1xx_xxxx
clar_int
Writing a logic 1 to this address bit
clears the interrupt.
TABLE 3. ENABLE
BIT 7
OPERATION
0
disable ADC-core to reset-mode (default)
1
enable ADC-core to normal operation
TABLE 4. ADCPD
BIT 6
OPERATION
0
Normal operation (default)
1
Power Down
TABLE 5. TIMING MODE
BIT 5
OPERATION
0
Internal Timing Mode. Integration time is internally
timed determined by f
OSC
, REXT, and number of
clock cycles.
1
External Timing Mode. Integration time is externally
timed by the I
2
C host.
TABLE 6. PHOTODIODE SELECT MODE; BITS 2 AND 3
BITS 3:2
MODE
0:0
MODE1. ADC integrates or converts Diode1 only.
Current is converted to an n-bit unsigned data.*
0:1
MODE2. ADC integrates or coverts Diode2 only.
Current is converted to an n-bit unsigned data.*
1:0
MODE3. A sequential MODE1 then MODE2
operation. The difference current is an (n-1) signed
data.*
1:1
No operation.
TABLE 7. WIDTH
BITS 1:0
NUMBER OF CLOCK CYCLES
2
16
= 65,536
2
12
= 4,096
2
8
= 256
2
4
= 16
0:0
0:1
1:0
1:1
TABLE 8. INTERRUPT FLAG
BIT 5
OPERATION
0
Interrupt is cleared or not triggered yet
1
Interrupt is triggered
ISL29003
相關PDF資料
PDF描述
ISL36356A-APDK-EVAL PRISM 11Mbps Wireless Local Area Network Access Point
ISL36356A-APDK PRISM 11Mbps Wireless Local Area Network Access Point
ISL3690IR-TK Dual Band Direct Conversion Transceiver
ISL3690IR Dual Band Direct Conversion Transceiver
ISL3690 DIODE ZENER SINGLE 1000mW 7.5Vz 34mA-Izt 0.05 10uA-Ir 5Vr DO41-GLASS 5K/REEL
相關代理商/技術參數
參數描述
ISL29003IROZ 功能描述:IC SENSOR LIGHT-DGTL I2C 6-ODFN RoHS:是 類別:傳感器，轉換器 >> 光學 - 光電探測器 - 環境光傳感器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 產品變化通告:Product Discontinuation 25/Jun/2012 標準包裝:2,500 系列:- 帶接近傳感器:無 波長:- 電源電壓:1.7 V ~ 2 V 電流 - 暗（標準）:- 電流 - 光（典型值）:- 輸出類型:數字 - I²C 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UDFN 裸露焊盤 包裝:帶卷 (TR)
ISL29003IROZ-EVALZ 功能描述:EVALUATION BOARD FOR ISL29003 RoHS:是 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
ISL29003IROZ-T7 功能描述:光學數位轉換器 ISL29003IROZ LIGHT-T O-DIGTL I2C GAIN RoHS:否 制造商:ams 數據總線寬度: 峰值波長:470 nm 最大工作頻率: 工作電源電壓: 工作電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:Chipscale-6 封裝:Reel
ISL29004IROZ 功能描述:IC SENSOR LIGHT-DGTL I2C 8-ODFN RoHS:是 類別:傳感器，轉換器 >> 光學 - 光電探測器 - 環境光傳感器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 產品變化通告:Product Discontinuation 25/Jun/2012 標準包裝:2,500 系列:- 帶接近傳感器:無 波長:- 電源電壓:1.7 V ~ 2 V 電流 - 暗（標準）:- 電流 - 光（典型值）:- 輸出類型:數字 - I²C 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UDFN 裸露焊盤 包裝:帶卷 (TR)
ISL29004IROZ-EVALZ 制造商:Intersil Corporation 功能描述:INTRFC LIGHT-TO-DGTL OUTPUT SENSOR - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*