- 您現在的位置：買賣IC網 > PDF目錄383130 > ISL4223EIR (INTERSIL CORP) RES, SM 1.3K OHM 1/10W 1% PDF資料下載
參數資料
| 型號： | ISL4223EIR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 通用總線功能 |
| 英文描述： | RES, SM 1.3K OHM 1/10W 1% |
| 中文描述： | DUAL LINE TRANSCEIVER, PQCC20 |
| 封裝： | 5 X 5 MM, PLASTIC, QFN-20 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 401K |
| 代理商： | ISL4223EIR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁
8
from initiating automatic powerdown for 100ms after
powering up. This gives the slow-to-wake peripheral circuit
time to reestablish valid RS-232 output levels.
The time to recover from automatic powerdown mode is
typically 100
μ
s.
INVALID Output
The INVALID output always indicates whether or not a valid
RS-232 signal (see Figure 6) is present at any of the receiver
inputs (see Table 2), giving the user an easy way to
determine when the interface block should power down.
Invalid receiver levels occur whenever the driving
peripheral’s outputs are shut off (powered down) or when the
RS-232 interface cable is disconnected. In the case of a
disconnected interface cable where all the receiver inputs
are floating (but pulled to GND by the internal receiver pull
down resistors), the INVALID logic detects the invalid levels
and drives the output low. The power management logic
then uses this indicator to power down the interface block.
Reconnecting the cable restores valid levels at the receiver
inputs, INVALID switches high, and the power management
logic wakes up the interface block. INVALID can also be
used to indicate the DTR or RING INDICATOR signal, as
long as the other receiver inputs are floating, or driven to
GND (as in the case of a powered down driver).
INVALID switches low after invalid levels have persisted on
all of the receiver inputs for more than 30
μ
s (see Figure 7).
INVALID switches back high 1
μ
s after detecting a valid
RS-232 level on a receiver input. INVALID operates in all
modes (forced or automatic powerdown, or forced on), so it
is also useful for systems employing manual powerdown
circuitry. When automatic powerdown is utilized, INVALID =
0 indicates that the ISL422XE is in powerdown mode.
Capacitor Selection
The charge pumps require 0.1
μ
F, or greater, capacitors for
proper operation. Increasing the capacitor values (by a factor
of 2) reduces ripple on the transmitter outputs and slightly
reduces power consumption.
When using minimum required capacitor values, make sure
that capacitor values do not degrade excessively with
temperature. If in doubt, use capacitors with a larger nominal
value. The capacitor’s equivalent series resistance (ESR)
usually rises at low temperatures and it influences the
amount of ripple on V+ and V-
.
Power Supply Decoupling
In most circumstances a 0.1
μ
F bypass capacitor is
adequate. In applications that are particularly sensitive to
power supply noise, decouple V
CC
to ground with a
capacitor of the same value as the charge-pump capacitor C
1
.
Connect the bypass capacitor as close as possible to the IC.
Transmitter Outputs when Exiting
Powerdown
Figure 8 shows the response of two transmitter outputs
when exiting powerdown mode. As they activate, the two
transmitter outputs properly go to opposite RS-232 levels,
with no glitching, ringing, nor undesirable transients. Each
transmitter is loaded with 3k
in parallel with 2500pF.
FIGURE 6. DEFINITION OF VALID RS-232 RECEIVER LEVELS
0.3V
-0.3V
-2.7V
2.7V
INVALID LEVEL - POWERDOWN OCCURS AFTER 30
μ
s
VALID RS-232 LEVEL - ISL422XE IS ACTIVE
VALID RS-232 LEVEL - ISL422XE IS ACTIVE
INDETERMINATE - POWERDOWN MAY OR
MAY NOT OCCUR
INDETERMINATE - POWERDOWN MAY OR
MAY NOT OCCUR
RECEIVER
INPUTS
TRANSMITTER
OUTPUTS
INVALID
OUTPUT
V+
V
CC
0
V-
V
CC
0
t
INVL
t
INVH
INVALID
REGION
}
FIGURE 7. AUTOMATIC POWERDOWN AND INVALID TIMING
DIAGRAMS
AUTOPWDN
PWR UP
ISL4221E, ISL4223E
相關PDF資料 |
PDF描述 |
|---|---|
| ISL4223EIRZ | QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kBps, RS-232 Transmitters/Receivers |
| ISL4223EIRZ-T | QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 150Nanoamp, 250kBps, RS-232 Transmitters/Receivers |
| ISL4241EIR-T | QFN Packaged, +/-15kV ESD Protected, +2.7V to +5.5V, 10Nanoamp, 250kbps, RS-232 Transmitters/Receivers |
| ISL4243EIR-T | CON BLOCK 2 ASY |
| ISL4243E | QFN Packaged, ±15kV ESD Protected, +2.7V to +5.5V, 10Nanoamp, 250kbps, RS-232 Transmitters/Receivers(QFN 封裝, ±15kV ESD防護, +2.7V至+5.5V, 10毫微安, 250kbps, RS-232收發器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL4223EIR-T | 功能描述:IC TXRX 2TX/2RX 3V RS-232 20-QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| ISL4223EIRZ | 功能描述:RS-232接口集成電路 3V RS-232 2TX/2RX TRANSC 20LD 5X5 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| ISL4223EIRZ-T | 功能描述:IC XMITTER/RCVR ESD RS232 20-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:發射器 驅動器/接收器數:4/0 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISL4223EIRZ-T7A | 功能描述:IC TXRX RS232 ESD 20QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:發射器 驅動器/接收器數:4/0 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISL4238E | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:QFN Packaged, 【15kV ESD Protected, +2.7V to +5.5V, 10Nanoamp, 250kbps/ 1Mbps, RS-232 Transceivers with Enhanced Automatic Powerdown |
發布緊急采購，3分鐘左右您將得到回復。