4
FN6054.3
October 28, 2010
DYNAMIC CHARACTERISTICS
Enable Turn-ON Time, tON
VS = ±4.5V, VNO or VNC = ±3V, RL = 300Ω, CL = 35pF,
VIN = 0 to 3 (See Figure 1) 25
-
35
-
ns
Full
-
45
-
ns
Enable Turn-OFF Time, tOFF
VS = ±4.5V, VNO or VNC = ±3V, RL = 300Ω, CL = 35pF,
VIN = 0 to 3 (See Figure 1) 25
-
22
-
ns
Full
-
27
-
ns
Address Transition Time, tTRANS
VS = ±4.5V, VNO or VNC = ±3V, RL = 300Ω, CL = 35pF,
VIN = 0 to 3 (See Figure 1) 25
-
43
-
ns
Full
-
53
-
ns
Break-Before-Make Time, tBBM
VS = ±5.5V, VNO or VNC = 3V, RL = 300Ω, CL = 35pF,
VIN = 0 to 3V (See Figure 3) Full
-
7
-
ns
Latch Setup Time, tS
25
-
25
-
ns
Full
-
35
-
ns
Latch Hold Time, tH
25
-
0
-
ns
Full
-
0
-
ns
Latch Pulse Width, tWPW
25
-
15
-
ns
Full
-
25
-
ns
Charge Injection, Q
CL = 1.0nF, VG = 0V, RG = 0Ω (See Figure 2) 25
-
0.3
-
pC
NO/NC OFF Capacitance, COFF
f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 8) 25
-
3
-
pF
COM OFF Capacitance, COFF
f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 8) 25
-
9
-
pF
COM ON Capacitance, CCOM(ON) f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 8) 25
-
14
-
pF
OFF Isolation
RL = 50Ω, CL = 15pF, f = 100kHz,
VNOx or VNCx = 1VRMS (See Figures 5, 7 and 20) 25
-
92
-
dB
25
-
<-110
-
dB
All Hostile Crosstalk (Note
8)25
-
-105
-
dB
POWER SUPPLY CHARACTERISTICS
Power Supply Range
Full
±2
-
±6
V
Positive Supply Current, I+
VS = ±5.5V, VINH, VADD = 0V or V+, Switch On or Off
Full
-7
-
7
A
Negative Supply Current, I-
Full
-1
-
1
A
NOTES:
4. VIN = Input logic voltage to configure the device in a given state.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6.
ΔRON = RON (MAX) - RON (MIN).
7. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
8. Between any two switches.
9. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
Electrical Specifications - 5V Supply
Test Conditions: VSUPPLY = ±4.5V to ±5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 4),
Unless Otherwise Specified. Boldface limits apply over the operating temperature range,
-40°C to +85°C. (Continued)
PARAMETER
TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 5, 9)
TYP
MAX
(Notes 5, 9) UNITS
ISL43231