- 您現在的位置：買賣IC網 > PDF目錄1927 > ISL54050IRUZ-T7A (Intersil)IC ANLG SWITCH DUAL SPDT 10TQFN PDF資料下載
參數資料
| 型號： | ISL54050IRUZ-T7A |
| 廠商： | Intersil |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ANLG SWITCH DUAL SPDT 10TQFN |
| 標準包裝： | 250 |
| 功能： | 開關 |
| 電路： | 2 x SPDT |
| 導通狀態電阻： | 500 毫歐 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 1.65 V ~ 4.5 V |
| 電流 - 電源： | 100nA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-UFQFN |
| 供應商設備封裝： | 10-UTQFN（1.8x1.40） |
| 包裝： | 帶卷 (TR) |
8
FN6356.4
November 22, 2008
Supply Sequencing and Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents,
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to GND (see
Figure 9). To prevent forward biasing these diodes, V+ must
be applied before any input signals, and the input signal
voltages must remain between V+ and GND.
If these conditions cannot be guaranteed, then precautions
must be implemented to prohibit the current and voltage at
the logic pin and signal pins from exceeding the maximum
ratings of the switch. The following two methods can be used
to provided additional protection to limit the current in the
event that the voltage at a signal pin or logic pin goes below
ground or above the V+ rail.
Logic inputs can be protected by adding a 1k
Ω resistor in
series with the logic input (see Figure 9). The resistor limits
the input current below the threshold that produces
permanent damage, and the sub-micro amp input current
produces an insignificant voltage drop during normal
operation.
This method is not acceptable for the signal path inputs.
Adding a series resistor to the switch input defeats the
purpose of using a low rON switch. Connecting Schottky
diodes to the signal pins, as shown in Figure 9, will shunt the
fault current to the supply or to ground thereby protecting the
switch. These Schottky diodes must be sized to handle the
expected fault current.
Power-Supply Considerations
The ISL54050 construction is typical of most single supply
CMOS analog switches, in that they have two supply pins:
V+ and GND. V+ and GND drive the internal CMOS
switches and set their analog voltage limits. Unlike switches
with a 4V maximum supply voltage, the ISL54050 5.5V
maximum supply voltage provides plenty of room for the
10% tolerance of 4.3V supplies, as well as room for
overshoot and noise spikes.
The minimum recommended supply voltage is 1.65V. It is
important to note that the input signal range, switching times,
and ON-resistance degrade at lower supply voltages. Refer
to the “Electrical Specifications” tables starting on page 3
and “Typical Performance Curves” on page 9 for details.
V+ and GND also power the internal logic and level shifters.
The level shifters convert the input logic levels to switched
V+ and GND signals to drive the analog switch gate
terminals.
This family of switches cannot be operated with bipolar
supplies, because the input switching point becomes
negative in this configuration.
Logic-Level Thresholds
This switch family is 1.8V CMOS compatible (0.5V and 1.4V)
over a supply range of 2.7V to 4.5V (see Figure 19). At 2.7V,
the VIL level is about 0.53V. This is still above the 1.8V
CMOS guaranteed low output maximum level of 0.5V, but
noise margin is reduced.
The digital input stages draw supply current whenever the
digital input voltage is not at one of the supply rails. Driving
the digital input signals from GND to V+ with a fast transition
time minimizes power dissipation.
The ISL54050 has been designed to minimize the supply
current whenever the digital input voltage is not driven to the
supply rails (0V to V+). For example, driving the device with
2.85V logic (0V to 2.85V) while operating with a 4.2V supply,
the device draws only 12A of current (see Figure 17 for
VIN =2.85V).
FIGURE 8. V+ SERIES RESISTOR FOR ENHANCED ESD AND
LATCH-UP IMMUNITY
IN
COM
100
Ω
NO
NC
V+
GND
C
OPTIONAL
PROTECTION
RESISTOR
FIGURE 9. OVERVOLTAGE PROTECTION
GND
VCOM
VNX
V+
INX
OPTIONAL
PROTECTION
RESISTOR
OPTIONAL
SCHOTTKY
DIODE
OPTIONAL
SCHOTTKY
DIODE
ISL54050
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54052IRUZ-T | IC SWITCH SPST 6UTDFN |
| ISL54053IRUZ-T | IC SWITCH SPDT 6UTDFN |
| ISL54055IRUZ-T | IC SWITCH SPST 6UTDFN |
| ISL54056IRUZ-T | IC SWITCH QUAD SPDT 16UTQFN |
| ISL54057IRUZ-T | IC SWITCH 4X1 16UTQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54051 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Ultra Low ON-Resistance, Low Voltage, Single Supply, Single SPST Analog Switches |
| ISL54051_0709 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Ultra Low ON-Resistance, Low Voltage, Single Supply, Single SPST Analog Switches |
| ISL54051IHZ-T | 功能描述:IC SWITCH SPST SGL SOT23-6 RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR) |
| ISL54051IRUZ-T | 功能描述:IC SWITCH SPST 6UTDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54052 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Ultra Low ON-Resistance, Low Voltage, Single Supply, Single SPST Analog Switches |
發布緊急采購，3分鐘左右您將得到回復。