- 您現在的位置：買賣IC網 > PDF目錄1927 > ISL54056IRUZ-T (Intersil)IC SWITCH QUAD SPDT 16UTQFN PDF資料下載
參數資料
| 型號： | ISL54056IRUZ-T |
| 廠商： | Intersil |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH QUAD SPDT 16UTQFN |
| 標準包裝： | 3,000 |
| 功能： | 開關 |
| 電路： | 4 x SPDT |
| 導通狀態電阻： | 550 毫歐 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 1.65 V ~ 4.5 V |
| 電流 - 電源： | 150nA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-UFQFN |
| 供應商設備封裝： | 16-UTQFN（2.6x1.8） |
| 包裝： | 帶卷 (TR) |
8
FN6357.4
August 15, 2007
Supply Sequencing and Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to GND (see
Figure 9). To prevent forward biasing these diodes, V+ must
be applied before any input signals, and the input signal
voltages must remain between V+ and GND.
If these conditions cannot be guaranteed, then precautions
must be implemented to prohibit the current and voltage at
the logic pin and signal pins from exceeding the maximum
ratings of the switch. The following two methods can be used
to provided additional protection to limit the current in the
event that the voltage at a signal pin or logic pin goes below
ground or above the V+ rail.
Logic inputs can be protected by adding a 1k
Ω resistor in series
with the logic input (see Figure 9). The resistor limits the input
current below the threshold that produces permanent damage,
and the sub-microamp input current produces an insignificant
voltage drop during normal operation.
This method is not acceptable for the signal path inputs.
Adding a series resistor to the switch input defeats the
purpose of using a low rON switch. Connecting Schottky
diodes to the signal pins as shown in Figure 9 will shunt the
fault current to the supply or to ground thereby protecting the
switch. These Schottky diodes must be sized to handle the
expected fault current.
Power-Supply Considerations
The ISL54056 construction is typical of most single supply
CMOS analog switches, in that they have two supply pins:
V+ and GND. V+ and GND drive the internal CMOS
switches and set their analog voltage limits. Unlike switches
with a 4.7V maximum supply voltage, the ISL54056 5.5V
maximum supply voltage provides plenty of room for the
10% tolerance of 4.3V supplies, as well as room for
overshoot and noise spikes.
The minimum recommended supply voltage is 1.65V. It is
important to note that the input signal range, switching times,
and ON-resistance degrade at lower supply voltages. Refer to
the “Electrical Specifications” table on page 5 and “Typical
Performance Curves” on page 9 for details.
V+ and GND also power the internal logic and level shifters.
The level shifters convert the input logic levels to switched
V+ and GND signals to drive the analog switch gate
terminals.
This family of switches cannot be operated with bipolar
supplies, because the input switching point becomes
negative in this configuration.
Logic-Level Thresholds
This switch family is 1.8V CMOS compatible (0.5V and 1.4V)
over a supply range of 3.0V to 4.5V (see Figure 19). At 3.0V
the VIL level is about 0.53V. This is still above the 1.8V
CMOS guaranteed low output maximum level of 0.5V, but
noise margin is reduced.
The digital input stages draw supply current whenever the
digital input voltage is not at one of the supply rails. Driving
the digital input signals from GND to V+ with a fast transition
time minimizes power dissipation.
The ISL54056 has been designed to minimize the supply
current whenever the digital input voltage is not driven to the
supply rails (0V to V+). For example driving the device with
2.85V logic (0V to 2.85V) while operating with a 4.2V supply
the device draws only 12
μA of current (see Figure 17 for
VIN =2.85V).
FIGURE 8. V+ SERIES RESISTOR FOR ENHANCED ESD AND
LATCH-UP IMMUNITY
INx
COMx
100
Ω
NOx
NCx
V+
GND
C
OPTIONAL
PROTECTION
RESISTOR
FIGURE 9. OVERVOLTAGE PROTECTION
GND
VCOM
VNX
V+
INX
OPTIONAL
PROTECTION
RESISTOR
OPTIONAL
SCHOTTKY
DIODE
OPTIONAL
SCHOTTKY
DIODE
ISL54056
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54057IRUZ-T | IC SWITCH 4X1 16UTQFN |
| ISL54058IRUZ-T | IC SWITCH DUAL 4X1 16UTQFN |
| ISL54059IRUZ-T | IC SWITCH DUAL SPDT 10UTQFN |
| ISL54061IRUZ-T | IC SWITCH DUAL SPST 10UTQFN |
| ISL54062IRUZ-T | IC SWITCH SPDT DUAL 10TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54057 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Ultra Low ON-Resistance, Low-Voltage, Single Supply, Differential 4 to 1 Analog Multiplexer |
| ISL54057IRUZ-T | 功能描述:IC SWITCH 4X1 16UTQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54058 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Ultra Low ON-Resistance, Low-Voltage, Single Supply, Dual 4 to 1 Analog Multiplexer |
| ISL54058IRUZ-T | 功能描述:IC SWITCH DUAL 4X1 16UTQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54059 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:+1.8V to +6.5V, Sub-Ohm, Dual SPDT Analog Switch with Negative Signal Capability |
發布緊急采購，3分鐘左右您將得到回復。