3
FN6379.0
September 29, 2006
Absolute Maximum Ratings
Thermal Information
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 4.7V
Input Voltages
INH, Ax, Bx, ADDx (Note
2) . . . . . . . . . . . . . . -0.3 to (V+) + 0.3V
Output Voltages
COMx (Note
2) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (V+) + 0.3V
Continuous Current NO or COM . . . . . . . . . . . . . . . . . . . . .
±300mA
Peak Current NO or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . .
±500mA
ESD Rating
HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >4kV
MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >300V
CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >1kV
Thermal Resistance (Typical, Note
3)θJA (oC/W)
TQFN Package . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
Maximum Junction Temperature (Plastic Package) . . . . . . +150°C
Maximum Storage Temperature Range. . . . . . . . . . . -65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C
(Lead Tips Only)
Operating Conditions
Temperature Range
ISL54057IRUZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on Ax, Bx, COMx, ADDx, or INH exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current
ratings.
3.
θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications: 3V Supply
Test Conditions: VSUPPLY = +2.7V to +3.3V, GND = 0V, VINH = 1.4V, VINL = 0.5V
(Notes
4, 8), Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP
(°C)
MIN
TYP
MAX
UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
Full
0
-
V+
V
ON Resistance, RON
V+ = 2.7V, ICOM = 100mA, VAX or VBX = 0V to V+
(See Figure )
25
-
0.43
0.75
Full
-
0.8
RON Matching Between Channels,
RON
V+ = 2.7V, ICOM = 100mA, VAX or VBX = Voltage at
25
-
0.09
0.2
Full
-
0.2
RON Flatness, RFLAT(ON)
V+ = 2.7V, ICOM = 100mA, VAX or VBX = 0V t0 V+
25
-
0.07
0.15
Full
-
0.15
Ax or Bx OFF Leakage Current,
IAx(OFF) or IBx(OFF)
V+ = 3.3V, VCOM = 0.3V, 3V, VAX or VBX = 3V, 0.3V
25
-4
-
4
nA
Full
-35
-
35
nA
COM ON Leakage Current,
ICOM(ON)
V+ = 3.3V, VCOM = VAX or VBX = 0.3V, 3V
25
-8.5
-
8.5
nA
Full
-60
-
60
nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, VINH, VADDH
Full
1.4
-
V
Input Voltage Low, VINL, VADDL
Full
-
0.5
V
Input Current, IINH, IINL, IADDH,
IADDL
V+ = 3.3V, VINH = VADD = 0V or V+
Full
-0.5
-
0.5
A
DYNAMIC CHARACTERISTICS
Inhibit Turn-ON Time, tON
V+ = 2.7V, VAx or VBx = 1.5V, RL = 50, CL = 35pF
25
-
27
-
ns
Full
-
37
-
ns
Inhibit Turn-OFF Time, tOFF
V+ = 2.7V, VAx or VBx = 1.5V, RL = 50, CL = 35pF,
25
-
18
-
ns
Full
-
28
-
ns
Address Transition Time, tTRANS
V+ = 2.7V, VAX or VBX = 1.5V, RL = 50, CL = 35pF
25
-
29
-
ns
Full
-
40
-
ns
Break-Before-Make Time, tBBM
V+ = 3.3V, VAX or VBX = 1.5V, RL = 50, CL = 35pF
25
-
4
-
ns
Full
-
1
-
ns
Ax or Bx OFF Capacitance, COFF
f = 1MHz, VAX or VBX = VCOM = 0V (See Figure )
25
-
44
-
pF
COM OFF Capacitance, COFF
f = 1MHz, VAX or VBX = VCOM = 0V (See Figure 6) 25
-
149
-
pF
COM ON Capacitance, CCOM(ON) f = 1MHz, VAX or VBX = VCOM = 0V (See Figure 6) 25
-
201
-
pF
ISL54057